WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

If your home’s wir- ing system is not a three-wire grounded system, do not use this electric starter under any conditions.

If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the separate engine manual packed separately with your snow thrower. Read instructions carefully.

Starting The Engine

1.Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

2.Make certain both the auger control and drive control are in the disengaged (released) position.

3.Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start unless the key is inserted into ignition switch.

Electric Starter (on certain models)

1.Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

1.Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

2.Rotate choke control to FULL choke position (for a cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

3.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

4.Push starter button to start engine.

5.Once the engine starts, immediately release starter button.

6.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

7.When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

1.Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

2.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Additional priming may be necessary if the temperature is below 15° F. (-9° C).

3.Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil.

4.Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil.

5.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again.

NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures.

Stopping The Engine

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

•To help prevent possible starter freeze-up, proceed as follows:

Electric Starter (on certain models)

1.Connect extension cord to the electric starter outlet on the engine, then to 120 volt AC outlet.

2.With the engine running, push the starter button and allow the starter for spin for several seconds. The noise made by the starter is normal. The engine’s starter is not being harmed.

10

Page 9 Page 11
Page 10
Image 10
Troy-Bilt 769-03800 warranty Gas & Oil Fill-Up, Stopping The Engine, Electric Starter on certain models
Page 9 Page 11

769-03800 specifications

The Troy-Bilt 769-03800 is a powerful and reliable rear-tine tiller designed to cater to both gardening enthusiasts and professional landscapers. Known for its durability and efficiency, this tiller boasts a robust design that makes it suitable for a variety of soil types, allowing users to prepare their garden beds with ease.

One of the standout features of the Troy-Bilt 769-03800 is its strong 14-inch steel tines, which are capable of slicing through hard-packed earth and clay with minimal effort. The tiller is equipped with a sizable 196cc engine that provides adequate power for tilling deeper and larger areas, ensuring that you can accomplish your gardening tasks quickly. The rear-tine configuration also means that the tiller can maneuver smoothly forward while the tines work through the soil, making the tilling process more efficient.

Another significant characteristic of this tiller is its adjustable tilling width. Users can choose between a range of widths from 16 inches to 24 inches, allowing for flexibility based on the specific needs of their garden or landscaping project. This feature enhances versatility, whether you are tackling narrow rows or wide garden plots.

The Troy-Bilt 769-03800 has a user-friendly control system, featuring an adjustable handlebar that accommodates various user heights and ensures comfort during operation. This ergonomic design reduces fatigue, making it easier to manage larger tilling projects.

In addition to its powerful performance, the tiller incorporates innovative technologies such as the patented "Bolo Tines," which are specially designed to break up soil more efficiently. This feature helps reduce the time and effort required for tilling, allowing users to achieve better results with less strain.

Safety is paramount with the Troy-Bilt 769-03800, as it includes features like a safety switch that ensures the engine can only be started when the user is ready. This prevents accidental starts and enhances overall user protection while operating the machine.

Overall, the Troy-Bilt 769-03800 is a versatile and robust tiller that combines power, efficiency, and user-friendly features. Whether you're a dedicated gardener or manage a larger landscape project, its reliable performance and innovative design make it a highly sought-after tool in the gardening community. For those looking to enhance their gardening experience, the Troy-Bilt 769-03800 is a worthwhile investment that promises to deliver exceptional results year after year.
Top Page Image Contents