3.When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

4.Move throttle control to STOP position.

5.Remove the ignition key (Do not turn key) to prevent unauthorized use of equipment.

6.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

NOTE: Keep the key in a safe place. The engine cannot start without the ignition key.

Recoil Starter

1.With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to engine.

2.Move throttle control to STOP position.

3.Remove the ignition key (Do not turn key) to prevent unauthorized use of equipment.

NOTE: Keep the key in a safe place. The engine cannot start without the ignition key.

4.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Auger Control Test

Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower), engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine.

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

7.To readjust the control cable, loosen the upper hex nut on the auger cable bracket. See Figure 4-2.

8.Position the bracket upward to provide more slack (or downward to increase cable tension).

9.Retighten the upper hex nut.

10.Repeat Auger Control Test to verify proper adjustment has been achieved.

Figure 4-2

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn 150°F (65°C). Do not touch.

When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower.

NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower

to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system.

11

Page 10 Page 12
Page 11
Image 11
Troy-Bilt 769-03800 warranty To Engage Drive, To Engage Augers, Recoil Starter, Auger Control Test
Page 10 Page 12

769-03800 specifications

The Troy-Bilt 769-03800 is a powerful and reliable rear-tine tiller designed to cater to both gardening enthusiasts and professional landscapers. Known for its durability and efficiency, this tiller boasts a robust design that makes it suitable for a variety of soil types, allowing users to prepare their garden beds with ease.

One of the standout features of the Troy-Bilt 769-03800 is its strong 14-inch steel tines, which are capable of slicing through hard-packed earth and clay with minimal effort. The tiller is equipped with a sizable 196cc engine that provides adequate power for tilling deeper and larger areas, ensuring that you can accomplish your gardening tasks quickly. The rear-tine configuration also means that the tiller can maneuver smoothly forward while the tines work through the soil, making the tilling process more efficient.

Another significant characteristic of this tiller is its adjustable tilling width. Users can choose between a range of widths from 16 inches to 24 inches, allowing for flexibility based on the specific needs of their garden or landscaping project. This feature enhances versatility, whether you are tackling narrow rows or wide garden plots.

The Troy-Bilt 769-03800 has a user-friendly control system, featuring an adjustable handlebar that accommodates various user heights and ensures comfort during operation. This ergonomic design reduces fatigue, making it easier to manage larger tilling projects.

In addition to its powerful performance, the tiller incorporates innovative technologies such as the patented "Bolo Tines," which are specially designed to break up soil more efficiently. This feature helps reduce the time and effort required for tilling, allowing users to achieve better results with less strain.

Safety is paramount with the Troy-Bilt 769-03800, as it includes features like a safety switch that ensures the engine can only be started when the user is ready. This prevents accidental starts and enhances overall user protection while operating the machine.

Overall, the Troy-Bilt 769-03800 is a versatile and robust tiller that combines power, efficiency, and user-friendly features. Whether you're a dedicated gardener or manage a larger landscape project, its reliable performance and innovative design make it a highly sought-after tool in the gardening community. For those looking to enhance their gardening experience, the Troy-Bilt 769-03800 is a worthwhile investment that promises to deliver exceptional results year after year.
Top Page Image Contents