TB32 EC
Operator’s Manual
Removing Unit From Carton | Assemble The Unit |
1 | 2 |
Remove all contents from | Place shield onto mount |
cartonhecarton. . | bracket. Securely screw 2 shield |
| screws through holes on mount |
| bracket and into shield. Make |
| sure screws are tightened equally |
| so there is an equal gap between |
| bracket and shield on each side. |
3
Remove cap from lower boom. Push cutting attachment into coupler. Turn coupler knob clockwise to tighten.
Min. 6
4
Put
Electric Starter or |
|
Power Start Bit Optional! | Starter Rope |
THESE OPTIONAL ACCESSORIES
ARE SOLD SEPARATELY!
This unit has an alternate starting method |
|
that many find easier to use than pulling a |
|
rope. Please contact a local retailer or call |
|
| |
Information may also be found at | On/ Off Switch |
www.troybilt.com |
|
Fuel Cap
Throttle Control
English — Page 1
Assemble The Unit |
|
| Starting The Unit |
|
|
| Primer |
|
|
| Bulb |
40:1 |
|
|
|
1 Gallon | 3.2 oz |
|
|
5 |
| 6 | 10 X |
| 7 | ||
Mix thoroughly in separate | Place unit on a level surface. | Press primer bulb 10 times, | |
fuel can: |
| Fill fuel tank. | or until fuel is visible |
–3.2 fl. oz. of
–1 gallon of unleaded
gasoline
NOTE: Do not mix directly in fuel tank.
Starting The Unit
Choke Lever
Cutting Head Shield
8
Move choke lever to
Position 1.
Assembly Tools
Required:
Phillips #2 Screwdriver
Need Help?
Call 1-800-828-5500
DIDN’T START?
Repeat these instructions.
IF engine fails to start after 2 attempts, move choke lever to position 3 and pull the starter rope until engine starts
IF unit still fails to start, refer to the
operator’s manual for additional starting
and troubleshooting information
Page 6
Choke Lever
Choke Lever
|
| 5 X |
|
|
| ||
19 | 10 | 11 | 12 | 14 | 15 | ||
13 | |||||||
Crouch in starting position. | SQUEEZE and HOLD | Pull rope 5 times. | Move choke lever to | Pull rope | Continue to squeeze | Continue to squeeze | |
| throttle for ALL further |
| Position 2 and squeeze | engine. Run unit for | throttle. Move choke lever | throttle. Run unit for an | |
| steps. |
| throttle. | seconds to warm up. | to Position 3. | additional 60 seconds to | |
|
|
|
|
|
| complete | |
|
|
|
|
|
| may be used during this | |
|
|
|
|
|
| time. |
Español —
Reloading the Line*
Bump 
Knob
Outer
Spool
Inner |
Top Hole
1
2 | Spring | Reel | 3 |
| |||
|
|
4
Bottom Hole
Split Wall
5
Holding Slots
6
Eyelets
7
Unscrew the bump knob counterclockwise.
Reloading the Line
18
Hold the inner reel and outer spool together. Firmly pull the two line ends to release them from the holding slots. Screw the bump knob on clockwise. Tighten the bump knob securely.
Remove the inner reel and | Cut one |
spring. | of new 0.095” split line |
| trimming line. Split each end |
| about 6 inches (150 mm). |
For replacement line, call
For single line installation or replacement spool installation instructions, refer to the Replacing the Trimming Line section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions are NOT part of the fast assembly instructions. Line does not need to be installed on the initial assembly and
Insert the end of one line into the top hole and the end of the other line into the bottom hole.
Wind the line tightly in the direction shown on the inner reel. The split wall will divide the line. Wind the line until it is completely divided and about 6 inches (150 mm) of line remains.
Insert the two
Pass the two line ends through the eyelets. Place the spring inside the inner reel. Insert the inner reel into the outer spool. Push the inner reel and outer spool together.
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP? CALL
11/11 |
