Uniden FP105 Storing ONE-TOUCH Speed Dial Numbers, Pause, Dialing the Stored Numbers, Calltimer

12 one-touch speed dial numbers can be programmed into the memory of your telephone, Each memory location can store a maximum of 32 digits.

➤STORING ONE-TOUCH SPEED DIAL NUMBERS

Eg : To program UNIDEN telephone number, 0295993577 into speed dial location 3

1.Press the store button (Display shows NUMBER ?).

2.Enter the phone number 0 2 9 5 9 9 3 5 7 7 using the keypad

3.Press the store button (Display shows NAME ?)

4.*Enter the name U N I D E N using the keypad

(88 66 444 3 >> 33 66)

5.Press the store button (display shows STORE TO?)

6.Press the speed dial button number 3

The phone will beep and the display will show STORED

*If you do not want to store a name, skip step 4

If you have to type in several letters (consecutively) contained in one button (i.e. D & E).

!	l
		you need to press >> to move the cursor to the next space prior to pressing the button
		again.
	l To add a space before another word, press 1 once. For more fhan one space, press >>.
		Repeated pressing of the keypad digit ‘1’ will step through the following symbols : - ' () &,
	l Repeated pressing of any other keypad digit will step through the letters and number
		associated with that key
		Examples A=2, B=22, C=222, 2=2222, D=3, E=33, F=333 3=3333
!	l Repeated pressing of the << or >>button will move the cursor backwards or
		forwards to the position required.
	l When the cursor is flashing on top of any character you can press the delete button
	.	to delete that character
		Always store area code together with telephone numbers. This will be useful for CID
	l
		purposes.

➤PAUSE

During the memory storage procedure, you may wish to press the rdl/p button to insert a pause between numbers. (This is sometimes useful for accessing a switch board, telephone banking or long distance dialling).

Pressing rdl/p button more than once will increase the pause between digits.

Each time the rdl/p button is pressed, a ‘P’ will show on the LCD to indicate a 2 second pause in the dialing sequence. Each pause counts as one digit.

➤MEMORY STORAGE CARD When you have programmed a number into the speed dial memory, you can write the name of the person on the memory storage card (supplied).

➤DIALING THE STORED NUMBERS

There are four different ways to dial a stored speed dial number, depending on your preference.

Pick up the handset and press the desired memory button (1 - 12).

Press the speaker button and then press the desired memory button (1 - 12).

Press the desired memory button (1 - 12), and check the LCD shows the correct information. Press the dial button (the phone enters speakerphone mode and dials the displayed number).

4.Press the desired memory button (1- 12), and check the LCD shows the correct information. Pick up the handset and then press the dial button.

!If you have selected a speed dial button that does not have a stored number, the telephone will not dial.

For options 3 & 4, the LCD will show <EMPTY> if there is no number stored in the memory button pressed.

➤CHAIN DIALING

On certain occasions (such as telephone banking), after dialing one number, you may wish to dial another number without hanging up. This is known as chain dialing or cascade dialing. Simply store the second number in another memory location and press the corresponding speed dial button when required. In this way you can recall both numbers that are stored into their own memory locations at the relevant times.

➤CALLTIMER

Approximately 10 seconds after the handset is picked up, or the speaker button is pressed, the call counter will begin and show the elapsed time on the display screen.

LCD BACKLIGHT DISPLAY	Uniden	y
The LCD has a back light that will turn on under the
following conditions;
l Any incoming call
l Picking up the handset
l Pressing any button

!The backlight will switch off automatically approximate/y 15 seconds after the last activity The AC Adpator must be plugged into the unit to enable BACK LIGHT to work.