Intdoor Electric Fireplace Model No. EF700SP
Operating Instructions
Do NOT use an extension cord because the extension cord may overheat and cause a risk of fire.
Before Turning “ON”
-AKE SURE ALL PACKAGING AND PROTECTIVE FILMS HAVE
BEEN REMOVED FROM THE ELECTRIC FIREPLACE |
|
%LECTRIC FIREPLACE SHOULD BE THOROUGHLY INSPECTED |
|
BEFORE EACH USE AND BY A QUALIFIED SERVICE PERSON AT | 0RODUCT SIZE |
LEAST ANNUALLY |
Note 7HEN THE MAIN POWER IS TURNED ON THE FIRE LOG | Illustration 5 | ||||
BRIGHTNESS IS FACTORY SET TO MEDIUM BRIGHTNESS |
| ||||
4O ADJUST THE FLAME LEVEL PRESS ONE OF THE FLAME BUTTON |
| ||||
|
|
|
| ||
h v MEANS MORE BRIGHTNESS |
|
| |||
hnv MEANS LESS BRIGHTNESS |
|
| |||
4O TURN HEAT LEVEL h/.v h/&&v PRESS THE HEAT BUTTON |
| ||||
|
|
|
| ||
Note THE BUTTON WILL TURN THE HEAT h/.v TO THE LEVEL SET |
| ||||
BY THE HEAT LEVEL CONTROL KNOB |
| ||||
0USH THE POWER BUTTON |
|
| TO TURN h/&&v |
| |
|
| ||||
|
| ||||
Turning “ON”
Note 4HIS DOES NOT TURN THE ENTIRE ELECTRIC FIREPLACE h/&&v THE ELECTRIC FIREPLACE IS IN THE hSTANDBY MODEv
Caution: Keep electric fireplace area clear and free from combustible materials, gasoline and other flammable
Illustration 1
Turning “OFF”
)NFRARED REMOTE
Caution: Do not obstruct the flow of ventilation air. 
IS IN THE h/&&v POSITION )LLUSTRATION
0LUG THE POWER CORD INTO A DRY 6 '&) 'ROUND &AULT
)NTERRUPTER PLUG OUTLET )LLUSTRATION
0USH THE MAIN POWER SWITCH TO THE h/.v POSITION )LLUSTRATION
!DJUST FLAME CONTROL KNOB | TO THE DESIRED SETTING |
Note: )F YOU DO NOT WANT THE FLAME TURN THE FLAME CONTROL KNOB TO THE TWELVE OCLOCK POSITION
4O TURN THE HEAT ON PUSH THE HEAT SWITCH | TO THE | |
h/.v POSITION |
|
|
!DJUST THE HEAT CONTROL KNOB | TO THE DESIRED | |
SETTING |
|
|
Note: )F YOU DO NOT WANT THE HEAT PUSH THE HEAT SWITCH TO THE h/&&v POSITION
Note &IRE LOG BRIGHTNESS CAN ONLY BE CONTROLLED BY USING THE REMOTE 4HERE ARE NOT SEPARATE CONTROLS FOR THE FIRE LOG BRIGHTNESS ON THE CONTROL PANEL
Note 7HEN THE MAIN POWER IS TURNED ON THE FIRE LOG BRIGHTNESS IS FACTORY SET TO MEDIUM BRIGHTNESS
OFF | Ma |
1. P | |
| 2. T |
| w |
ON | i |
3. A | |
| s |
Illustration 2
#ONNECTING THE POWER CORD TO A
DRY '&) PLUG OUTLET
0USH THE MAIN POWER SWITCH | TO THE h/&&v POSITION |
5NPLUG THE POWER CORD FROM THE WALL OUTLET
Cleaning and Care
Notices
1. | Abrasive cleaners will damage this product. |
2. | Never use oven cleaner to clean any part of electric fireplace. |
3. | Do not clean any electric fireplace part in a self cleaning oven. The extreme heat will |
| damage the finish. |
4. | More frequent cleaning may be required as necessary. It is imperative that control |
| compartment, ventilation openings of the electric fireplace be kept clean. |
5. | Inspect electric fireplace before each use. |
6. | Have electric fireplace inspected annually and repairs should be made by a qualified |
| service person. |
7. | Check electric fireplace immediately if any of the following conditions exist: |
| a. You see sparks around the electrical outlet, power cord or inside the fireplace. |
| b. Any part of the power cord is cut. |
| c. Any strange noise, smell or smoke. |
8. | Do not paint any part of the electric fireplace firebox. |
9. | This electric fireplace should be thoroughly checked and cleaned on a regular basis. |
Using Remote Control
Note: Once the remote is used, the control panel knobs are disabled.
Note: To enable the control panel knobs push the main
power switch ( 
) on the control panel to the “OFF” position, wait 5 seconds, then push the main power switch to the “ON” position.
Note: The effective range of the remote control is up to 19.7 ft. (6 m).
)NSERT !!! BATTERIES ./4 ).#,5$%$ INTO THE BACK OF THE REMOTE
Note: Do NOT mix old and new batteries.
Note: Do NOT mix alkaline, standard
)F THE ELECTRIC FIREPLACE IS UNPLUGGED
A 
IS IN THE h/&&v POSITION )LLUSTRATION
B 0LUG THE POWER CORD INTO A DRY 6 '&) 'ROUND &AULT )NTERRUPTER PLUG OUTLET )LLUSTRATION
C 0USH THE MAIN POWER SWITCH TO THE h/.v POSITION )LLUSTRATION
)F THE ELECTRIC FIREPLACE IS PLUGGED INTO A DRY '&) OUTLET
A 0USH THE MAIN POWER SWITCH TO THE h/.v POSITION )LLUSTRATION
4O ADJUST THE FIRE LOG BRIGHTNESS PRESS ONE OF THE LOG
BUTTON 
h v MEANS MORE BRIGHTNESS hnv MEANS LESS BRIGHTNESS
Note &IRE LOG BRIGHTNESS CAN ONLY BE CONTROLLED BY USING THE REMOTE 4HERE ARE NOT SEPARATE CONTROLS FOR THE FIRE LOG BRIGHTNESS ON THE CONTROL PANEL
Illustration 3
OFF | Mai |
1. P | |
| 2. T |
| w |
ON | is |
3. A | |
| s |
Illustration 4
t. | OFF |
ch
ON
(EAT POWER AND HEAT CONTROL
10. After a period of storage and/or non use, ventilation obstructions and inspect for any |
abrasion, wear, cuts to the power cord. |
Cleaning Surfaces
7IPE SURFACES CLEAN WITH MILD DISHWASHING DETERGENT OR BAKING SODA
&OR STUBBORN SURFACES USE A CITRUS BASED DEGREASER AND A NYLON SCRUBBING BRUSH 2INSE CLEAN WITH DAMP CLOTH
Note 7HILE CLEANING YOUR UNIT BE SURE TO KEEP THE AREA AROUND THE HEATING ELEMENT DRY AT ALL TIMES $O NOT SUBMERGE THE HEATING ELEMENT ASSEMBLY )F THE HEATING ELEMENT IS SUBMERGED IN WATER DO ./4 USE IT )T MUST BE REPLACED
Maintenance
4O ENJOY YEARS OF OUTSTANDING PERFORMANCE FROM YOUR ELECTRIC FIREPLACE MAKE SURE YOU PERFORM THE FOLLOWING MAINTENANCE ACTIVITIES ON A REGULAR BASIS
+EEP EXTERIOR SURFACES CLEAN
!IR FLOW MUST BE UNOBSTRUCTED +EEP CIRCULATING AIR PASSAGEWAYS CLEAN