Installation

Please see all methods of Installation in Appendix at the rear of this booklet.

This is a furnace, not a free standing stove. You must direct heated air from 12" outlet away from the furnace, or it will not function properly.

1.This installation must be done by a qualified heating equipment installer.

2.The installation is to be done in compliance with National Fire Protection Association installation standards: No. 89M, 90B, 211, 70 (National Electric Code) and Uniform Mechanical Code 913, 6-4, in the states where applicable. (Their code offers connecting smoke pipe connectors into chimney with other fuel burning appliances.)

3.Rooms large in comparison with size of the appliances:

a)A Wood Burning Furnace needs air for combus- tion and circulation to house.

b)Provision must be made to make up this air and not starve gas or oil furnace of combustion air.

c)Have "Authority Having Jurisdiction" determine that air is of adequate makeup. (Reference N.F.P.A. Nos. 30 & 54, Code for Installation of Gas & Oil Equipment)

4.Have "Authority Having Jurisdiction" to inspect all chimneys and installations for adequate venting and for compliance with standard and local codes and regula- tions regarding installation of wood burning appliances.

5.Installation of Supplemental Heat Application to Existing Central System. (See Fig. 12 for typical instal- lation.)

a)Place Wood Burning Furnace so that the chimney connector will be as short as possible and avoiding unnecessary sharp turns in the smoke pipe connector and the installation of devices that would create excessive resistance to the flow of flue gases.

b)Locate the Wood Burning Furnace as close as practical to the existing central hot air heating system, maintaining clearances as stated on the label located on the side of the furnace.

c)Clearances from combustible materials must be complied with as stated on the label below the fuel door:

Unit to Combustible:

Front: 48"

Back: 30"

Sides: 12"

Plenum to Ceiling: 6"

Pipe to Combustible:

Sides: 21"

Back: 18"

The installation must be made only on a noncombustible floor.

d)Install the smoke pipe connector to the chimney with 26-gauge pipe and elbows (to be purchased sepa- rately), maintaining the proper clearances for the spe- cific model. Make sure that the proper clearances as stated on the label and earlier in this manual are maintained. Seal the smoke pipe in the chimney with furnace cement. (The chimney connector shall be se- curely supported, and joints fastened with sheet metal screws or rivets.)

e)Install 8" diameter heat pipe to plenum of the central hot air furnace. Use 26-guage pipe and connec- tors (to be purchased separately). (See Fig. 13) If central air conditioning is installed in the plenum, install heat pipe above the air conditioning unit. Secure heat pipe connection with supports and sheet metal screws.

f)Connect electrical supply in the electrical junction box that is mounted on the back of the Wood Burning Furnace. See Wiring Diagram (Fig. 11). Re- move the cover from electrical junction box connect power supply wires to wires designated, using wire nuts. The power cord supplied may be used for installation, if permitted by local codes and regulations. If the power cord supplied cannot be used, the power supply wiring must be 90 degrees Centigrade in a metal cable and should be completed by a qualified installer complying with NFPA Standard No. 70 and local codes.

g)Optional Plenum Fan Control Switch (Part No. 11PCS) is available for installation on the plenum of central hot air heating furnace. The purpose of this switch is to activate the circulating fan of the central hot air heating furnace when the temperature in the plenum exceeds 120° Fahrenheit. The switch would activate the fan at 120° Fahrenheit, and would shut off the circulating fan when the temperature in the plenum is reduced to 100° Fahrenheit . This avoids overheating the plenum.

The electrical supply for operation of this fan control switch is to be obtained from same electrical supply as the central hot air heating system. (See Fig. 13) Follow the instructions of the wiring diagram (Fig. 14). Do not make connections across Limit Control in the furnace.

Make electrical connections in electrical junction box presently mounted on the furnace. Make electrical connections in accordance with NFPA Standard No. 70 and local codes in the power supply junction box (See Fig. 14). The wiring to complete the connections should be 18 AWG minimum copper and 90° Centigrade in a cable.

NOTE: THE MAXIMUM STATIC PRESSURE AT THE CENTRAL OR COMBINED PLENUM MUST NOT

EXCEED 0.12 INCHES WATER COLUMN.

•DRAWINGS FOR ILLUSTRATION PURPOSES ONLY•

13

Page 12 Page 14
Page 13
Image 13
United States Stove 1200G owner manual Installation
Page 12 Page 14

1200G specifications

The United States Stove 1200G is an efficient and stylish solution for homeowners seeking to enhance their heating capabilities while enjoying the aesthetic appeal of a traditional wood-burning stove. This model combines advanced technology with user-friendly features, making it a popular choice among consumers looking to heat their homes sustainably and economically.

One of the main features of the 1200G is its robust construction, made from heavy-duty steel. This ensures durability and longevity, allowing homeowners to enjoy their stove for years to come. The stove comes with a large firebox, accommodating more significant amounts of wood, which means longer burn times and less frequent reloading. This feature is particularly beneficial for those looking to minimize maintenance while maximizing heat output.

The United States Stove 1200G boasts a powerful heating capacity, able to easily heat spaces of around 1,200 square feet. Its efficient design ensures that it can produce ample warmth even during the coldest winter months. Moreover, the stove is equipped with a secondary combustion system which enhances efficiency by allowing for more complete burning of fuel. This not only improves the stove’s performance but also minimizes emissions, making it environmentally friendly.

Another important characteristic of the 1200G is its user-friendly features. The glass door allows for a beautiful view of the fire while providing easy access to the firebox. The stove is also designed with adjustable air controls that enable users to manage the burn rate of the fire, providing flexibility in temperature regulation. This feature is ideal for those who want to tailor the heating experience to their specific comfort level.

Additionally, the 1200G is designed for easy installation, fitting into a variety of home layouts without requiring extensive modifications. It complies with EPA standards, demonstrating its commitment to reducing environmental impact while providing a reliable heating solution.

In summary, the United States Stove 1200G is a blend of traditional aesthetics and modern technology, making it a desirable choice for those seeking an effective wood-burning stove. Its robust construction, efficient heating capabilities, user-friendly features, and compliance with environmental standards position it as a strong contender in today’s market for home heating solutions.
Top Page Image Contents