Manuals / Varimixer / Kitchen Appliance / Mixer

Varimixer W100, 40 Function, Explanation, Enter, Used for stepping through a program, is running

Models: 60 W80 40 MK IV W100

1 32

Page 5

ITEM	FUNCTION	EXPLANATION
6.	Enter	Used for stepping through a program.
7.	CLR	Clears a flashing display.
8.	Speed up/down arrows.	Used for adjusting the the speed while the mixer
		is running.
9.	Time up/down arrows.	Used for adjusting the the time.
10.	Program	Used to enter/exit program-programming mode.
11.	Pause	Pauses the mixer without losing recipe.
12.	Numeric keys	Used for setting time and speed.
13.	Emergency Stop	Stops the mixer instantly.
14.	Start	Starts the mixer.
15.	Stop	Stop and reset key - reduces the speed to
		minimum and stops the mixer.
16.	Bowl Lift	If available, used for raising and lowering the
		mixing bowl.
17.	Green L.E.D.	Lights up when mixer is paused.

How to run the mixer manually.

R.P.M. Mode.

Enter the speed desired.

Push

Enter the time desired.

Push

Page 5

Image 5

Varimixer W100 Function, Explanation, Enter, Used for stepping through a program, Clears a flashing display, is running

Contents

User’s Manual MK-IVTHE PROGRAMMABLE CONTROL SYSTEM Page General descriptions MODES The system contains six different modes 3. PROGRAM MODE The mode where all programmed recipes are executed5. RPM MODE Computer displays the speed in actual R.P.M 6. SPEED MODE Computer displays the speed speed 1, 2, 3 andFUNCTION The Keypad The Keypad is used for entering data to the systemEXPLANATION Program NoUsed for adjusting the the time Used for adjusting the the speed while the mixerUsed for setting time and speed Stop and reset key - reduces the speed toStep “HOLD FOR 3 SECONDS” The mixer will only run recipes that are programmed To run a programmed recipe Push Enter the Program number Push PushFixed Mode To enter “FIXED MODE” Push “HOLD FOR 3 SECONDS”Push “99” Push Push “1 2 3 4” Push Push the program number Push To exit “FIXED MODE”“HOLD FOR 3 SECONDS” A D B C Error Codes 1.5 Amp “HOLD FOR 3 SECONDS” To correct this error PushP.N. 60E-517.02 Power Supply 1 Fuse1.5 Amp 6.3 x 32 MM P.N. 20E-418 MAINTENANCE AND ADJUSTMENTS Fuse data and component locationBowl Lift Microswitches PN 61-522 Each Computer Control 2 Fuses 8 Amp 6.3 x 32 MM P.N. 20E-418.1W40 = 6 3/8” W60 = 7” Bowl adjustments Models W30, W40, W40P, W60,W60P W30 = 6 3/8”W150 = 11 7/8” Bowl adjustments Models W80, W100, W150N W80 = 9 1/8” W100 = 11 5/8”White Lithium Grease IE Lubriplate LubricationLEAVE AGAINST ARM 2. If the main vari belt A appears loose when the Belt adjustmentsB Pry upper spring fork assembly N off of shaft D Reinstall spring fork assembly N , washersBelt Exchange Installing and tightening of V-beltsBelt Exchange Adjustment of low and high speed microswitches Adjustment of low and high speed microswitches OR O.D. of Pin.to determine correct part number Measure I.D. of holeSpeed Servo System Auxilliary Switch Power SupplyFigure Number DescriptionPower Supply Page Page 1.5 Amp Power Supply Wiring DiagramPage 5489 Campus Drive Shreveport LA 800 318 635-3131 Fax

Enter

Used for stepping through a program.

Clears a flashing display.

Speed up/down arrows.

Used for adjusting the the speed while the mixer

is running.

Time up/down arrows.

Used for adjusting the the time.

Program

Used to enter/exit program-programming mode.

Pause

Pauses the mixer without losing recipe.

Numeric keys

Used for setting time and speed.

Emergency Stop

Stops the mixer instantly.

Start

Starts the mixer.

Stop

Stop and reset key - reduces the speed to

minimum and stops the mixer.

Bowl Lift

If available, used for raising and lowering the

mixing bowl.

Green L.E.D.

Lights up when mixer is paused.

How to run the mixer manually.

Push