VEC1043_ManualEN_091505 1/17/06 5:49 PM Page 4

CAUTION

The Power Inverter must be connected only to batteries with a nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery and will sustain permanent damage if connected to a 24 volt battery.

Connection to a Power Source

The Power Inverter comes equipped with battery clip cables for connection to a power source.

CAUTIONS

Do not use with positive ground electrical systems.

Reverse polarity connection will result in a blown fuse and may cause permanent damage to the inverter.

Notes: Most vehicle accessory outlet circuits have fuses rated at 15 to 20 amps or greater. To operate at full wattage, either use the battery clip cable (supplied) or directly wire to the power source with user-supplied wire and fuse.

The majority of modern automobiles, RVs and trucks are negative ground.

Connecting to a Power Source Using the Provided Cables

Use the provided cables and connect the Power Inverter directly to the 12 volt power source as follows:

1.Make sure the Power Inverter power is turned OFF and that no flammable fumes are present in the installation area.

2.Connect the RED cable to the RED post marked (+) on the back of the inverter. Connect the battery clip to the POSITIVE terminal of the battery.

3.Connect the BLACK cable to the BLACK post marked (–) on the back of the inverter. Connect the battery clip to the NEGATIVE terminal of the battery.

4.Make sure that all connections between battery clips and terminals are secure.

Direct Hardwiring to Power Source

Use #8 AWG wire if the inverter to power source connection is 4 feet or less. For longer cable lengths use #6 AWG wire (to 10 feet). In either case, protect the positive

(+)wire from shorts by installing a 150-200 amp fuse or circuit breaker close to the DC power source (battery) terminal.

1.Check to be sure the inverter’s power switch is turned OFF and that no flammable fumes are present.

2.Identify the POSITIVE (+) and NEGATIVE (–) DC power source (battery) terminals.

3.Install a fuse holder or breaker close to the POSITIVE (+) terminal of the DC source (battery).

4.Connect a length of wire on one side of the fuse holder or circuit breaker. Connect the other end of the wire to the POSITIVE (+) terminal of the inverter.

5.Connect a length of wire between the inverter’s NEGATIVE (–) terminal and the DC power source NEGATIVE (–-) terminal.

6.Connect a short length of wire to the other terminal of the fuse holder or circuit breaker. Mark it “POSITIVE” or “+”.

7.Connect the free end of the fuse or breaker wire to the POSITIVE (+) terminal of the DC power source (battery).

8.Insert a fuse appropriate to the inverter in the fuse holder.

9.Test the inverter by turning it on and plugging in a 100 watt lamp or equipment.

10.If the inverter is not operating properly, then refer to the “Troubleshooting” section of this manual.

CAUTIONS

Loose connectors may cause overheated wires and melted insulation.

Check to make sure you have not reversed the polarity. Damage due to reversed polarity is not covered by our warranty.

Connection To Load

The Power Inverter is equipped with a standard North American three-prong type outlet. Plug the cord from the equipment you wish to operate into the AC outlet. Make sure the load requirement of your equipment does not exceed 750 watts.

The Power Inverter is engineered to be connected directly to standard electrical and electronic equipment in the manner described above. Do not connect the Power Inverter to household or RV AC distribution wiring. Do not connect the Power Inverter to any AC load circuit in which the neutral conductor is connected to ground (earth) or to the NEGATIVE of the DC (battery) source.

WARNING

Do not connect to AC distribution wiring!

CAUTION – Rechargeable Devices

Certain rechargeable devices do not operate well from a modified sine wave inverter. They only operate properly from a standard household outlet which provides a pure sine wave. Therefore, Vector recommends that these types of devices be operated from a standard household outlet only, not from the inverter.

This problem does not occur with the majority of battery-operated devices. Most of these devices use a separate charger or transformer that is plugged into an AC outlet. This inverter is easily capable of operating most chargers and transformers.

Placement of the Inverter

For best operating results, the inverter should be placed on a flat surface, such as the ground, car floor or seat, or other solid surface. A power cord has been provided for easy positioning of the inverter. The inverter should only be operated in locations that meet the following criteria:

DRY – Do not allow water and/or other liquids to come into contact with the inverter.

COOL — Surrounding air temperature should be between –0°C and 40°C — ideally between 15°C and 25°C (60-80°F). Keep the inverter away from direct sunlight, when possible.

VENTILATED – Keep the area surrounding the inverter clear to ensure free air circulation around the unit. Do not place items on or over the inverter during operation. A fan is helpful if the inverter is operating at maximum power outputs for extended periods of time. The unit will restart after it cools.

SAFE – Do not use the inverter near flammable materials or in any locations that may accumulate flammable fumes or gases.

4

5

Page 5
Image 5
Vector VEC1043 user manual Connection to a Power Source, Connection To Load, Placement of the Inverter

VEC1043 specifications

The Vector VEC1043 is a versatile and robust electric commuter bicycle specifically designed for urban environments. This innovative e-bike combines practicality with modern design, making it an ideal choice for city dwellers seeking an eco-friendly transportation solution.

One of its standout features is the powerful 250W brushless motor, integrated into the rear wheel hub, providing smooth and efficient power assistance. This motor ensures that riders can easily tackle inclines and longer distances without excessive exertion, making daily commutes efficient and enjoyable. With a pedal-assist system, the VEC1043 allows riders to choose their level of support, enabling a customizable riding experience based on personal preferences and fitness levels.

The VEC1043 is equipped with a high-capacity lithium-ion battery that provides an impressive range of up to 50 miles on a single charge. This battery can be conveniently charged in under 4 hours, making it perfect for those who need to recharge between rides. Additionally, the bike offers a battery management system designed to enhance longevity and efficiency, ensuring that cyclists can rely on their bike for years.

In terms of construction, the VEC1043 features a durable aluminum frame, balancing strength with lightweight properties for easy maneuverability. The bike’s ergonomic design includes an adjustable seat and handlebars, providing a comfortable ride for various rider heights.

Safety is a priority for the VEC1043, which is equipped with front and rear LED lights for enhanced visibility during nighttime rides. The bike also features a reliable braking system, comprising mechanical disc brakes that offer consistent stopping power in diverse weather conditions, ensuring the rider's safety at all times.

The VEC1043 comes with a user-friendly LCD display that shows essential riding data, including speed, distance, battery level, and assistance level. This intuitive interface allows riders to easily monitor their journey, enhancing the overall riding experience.

Overall, the Vector VEC1043 is a well-rounded electric bike that offers an efficient, practical, and enjoyable riding experience. With its combination of advanced technology, durable construction, and thoughtful features, it caters to the modern commuter's needs, making it an excellent choice for those looking to embrace sustainable transport options.