VEC128SL_ManualEN_092605 9/26/05 9:20 AM Page 9

7.LANTERN TUBE REPLACEMENT

The Lantern fluorescent tube is mounted on a socket assembly. Power is sent to the tube socket through the two support rods. It is very important to make sure the Lantern switch is turned OFF before removing the end cap. If there are any doubts about the ON/OFF switch being Off, then refer to the Battery Removal section and disconnect the battery before removing the end cap.

WARNING:

FLUORESCENT TUBES OPERATE WITH HIGH VOLTAGE.

DO NOT REMOVE END CAP UNLESS POWER IS OFF

AND THE BATTERY IS DISCONNECTED. SEE SECTION 9

See Figure 4 for Fluorescent Tube Replacement

 

 

 

FIGURE 4

3

4

 

5

 

 

 

 

 

 

 

12

6

1. DOME

2. TWIN TUBE FLUORESCENT

3. TUBE SOCKET ASSEMBLY

4. NUTS

5. END CAP

6. SUPPORT RODS

7.1 FLUORESCENT TUBE REMOVAL

1.Make sure that the Power Switch is Off AND the battery is disconnected.

2.Remove the set screw from the end cap - item #5.

3.Rest the unit on a secure tabletop.

4.Position the head to be in the Spotlight position.

5.Unscrew (counter clockwise) the End Cap and set aside.

6.Unscrew (counter clockwise) the two nuts from the two support rods and set them aside.

7.Slide the Tube Socket assembly away from the head and remove it from the two support rods.

8.Set it on a stable work surface like a table, bench,etc.

9.Grasp the Tube Socket and push on the fluorescent tube base to disconnect the tube from the socket.

10.Do not allow the tube to drop.

11.Follow local procedures for safe fluorescent tube disposal.

5

2.FEATURES

1,000,000 Power SeriesSpotlight

Powerful replaceable H-3 Series 6 volt quartz halogen bulb in spotlight

Powerful replaceable 13 watt fluorescent U-shaped twin tube in lantern

Head swivels 90 degrees for soft, 360 degree area lighting

Rubber safety guard protects spotlight

Recharging LED and battery FULL LED

Recharges from standard North American Standard 120 volt AC, 60 Hz, receptacle

Recharges from 12 volt DC accessory socket

Three way switch - Spotlight, Off and Lantern

Comfortable handgrip

Stable base prevents tip over in any head position

NOTE:

This unit is shipped in a partially charged state. Charge unit using either AC or DC method until the green LED lights. Charge after each use. Initial charge should be for 12 hours.

3.OPERATION

The swivel action of the unit keeps the lamp head securely in position for use while carrying or while on tabletop. The range of swivel motion is greater than 90 degrees with five locking positions. The spotlight position (upright) focuses light straight ahead. The lantern position (spotlight tilted forward 90 degrees) floods light in a 360-degree pattern for reading, cooking and many other uses. A three-position Power Switch (Spotlight, Off, Lantern) controls on/off operation of both lights. The switch is protected by a flexible covering that protects it from dust, dirt and moisture. This ensures reliability and extends the life of the switch. The spotlight can be continuously lit for up to 20 minutes on a full battery charge; the lantern can be lit for up to four hours on a full battery charge.

4.RECHARGE

All batteries lose charge over time, especially when they are warm. Frequent battery recharges will extend battery life. AC recharge is recommended every two months, when not in frequent use. Use the AC recharge adapter and charge until battery is full. AC and DC recharge connections are through a heavy-duty barrel receptacle at the lower rear of the unit. (See figure 5A) Two LED indicators display the status of recharge. Continue recharge operation until the two LEDS are equally bright. (See Figure 1A.)

2

Page 5
Image 5
Vector VEC1285L user manual Lantern Tube Replacement, Features, Operation, Recharge, Fluorescent Tube Removal