MENU MODE

MODE-SSB GROUP

082 J3E MIC SEL

Function: Selects the microphone to be used on the SSB modes (LSB and USB).

Available Values: Frnt/dAtA/PC

Default Setting: Frnt

Frnt (FRONT):Selects the microphone connected to

 

the front panel’s MIC jack while using

 

the SSB modes.

dAtA:

Selects the microphone connected to

 

pin 1 of the PACKET Jack while us-

 

ing the SSB modes.

PC:

This parameter is for future expansion

 

of this transceiver’s capabilities, but at

 

this time is not supported.

083 J3E TX BPF

Function: Selects the audio passband of the DSP modulator on the SSB mode.

Available Values: 1-30/1-29/2-28/3-27/4-26/3000 1-30: 50-3000(Hz)

1-29: 100-2900(Hz)

2-28: 200-2800(Hz)

3-27: 300-2700(Hz)

4-26: 400-2600(Hz)

3000: 3000WB

Default Setting: 3-27 (300-2700 Hz)

NOTE:

The apparent power output, when using the widest band- widths, may seem lower. This is normal, and it occurs because the available transmitter power is distributed over a wider bandwidth. The greatest compression of power out- put, conversely, occurs when using the “4-26” setting (400- 2600 Hz), and this setting is highly recommended for contest or DX pile-up work.

084 J3E LSB CAR

Function: Adjusts the receiver carrier point for the Main band’s (VFO-A) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz steps)

Default Setting: 0 Hz

085 J3E USB CAR

Function: Adjusts the receiver carrier point for Main band’s (VFO-A) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

086 J3E SLSB CR

Function: Adjusts the receiver carrier point for the Sub band’s (VFO-B) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

087 J3E SUSB CR

Function: Adjusts the receiver carrier point for Sub band’s (VFO-B) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

Page 120

RX AUDIO GROUP

088 rout AGC SLP

Function: Selects the gain curve of the AGC amplifier.

Available Values: nor/SLP

Default Setting: nor

nor (NORMAL): The AGC output level will follow a linear response to the antenna input level, while AGC is activated.

SLP (SLOPED): The AGC output level will increase at 1/10 the rate of the antenna input level, while AGC is activated.

Output

 

 

SLOPE

 

 

 

 

 

 

 

NORMAL

Audio

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input Signal

089 rout HEADPHN

Function: Selects one of three audio mixing modes when using headphones during Dual Receive operation. Available Values: SEP/Con1/Con2

Default Setting: SEP

SEP (SEPARATE): Audio from the Main (VFO-A) receiver is heard only in the left ear, and Sub (VFO-B) receiver audio solely in the right ear.

Con1 (COMBINE 1): Audio from both Main (VFO-

A)and Sub (VFO-B) receivers can be heard in both ears, but Sub (VFO-B) audio is attenu- ated in the left ear and Main (VFO-A) audio is attenuated in the right ear.

Con2 (COMBINE 2): Audio from both Main (VFO-

A)and Sub (VFO-B) receivers is combined and heard equally in both ears.

FT-2000 OPERATING MANUAL