VXA-710 SPIRIT OPERATING MANUAL
47
MENU (“SET”) MODE
MENU Listing
A listing of the Menu items available via the SET mode may be found below.
Available Values (Default: Bold Itaric)
On / Off
Key / Off / On
Off / On
00 - 15 (06)
LV 1 – LV 4 (LV 3)
Four patterns
Off / Temp / Volt
R: 000 - 255, G: 000 - 255, B: 000 - 255 (R: 000, G: 065, B: 000)
R: 000 - 255, G: 000 - 255, B: 000 - 255 (R: 111, G: 000, B: 000)
R: 000 - 255, G: 000 - 255, B: 000 - 255 (R: 127, G: 127, B: 127)
R: 000 - 255, G: 000 - 255, B: 000 - 255 (R: 000, G: 127, B: 000)
R: 000 - 255, G: 000 - 255, B: 000 - 255 (R: 127, G: 000, B: 127)
On / DTMF / Off
On / Off
Off / 1 / 2 / 3
0 - 8 (6)
0 - 8 (3)
5secs / Busy
DW / PRI
ABS/1:1/1:2/1:3/1:4/1:5/Off
5k / 10k / 12.5k / 15k /20k / 25k / 50k / 100k
500ms / 1s / 1.5s / 2s / 2.5s / 3s
±30ch / ±15ch
Off / TSQ / DCS
39 standard CTCSS tones (67.0 Hz)
106 standard DCS codes (023)
Off / 1min / 3min / 5min
DIAL / KEY / KEY+DIAL /PTT / DIAL+PTT /KEY+PTT / ALL
121.5 / HOME
ANL / XFER / SPEC Start / Large Font / None
ANL / XFER / SPEC Start / Large Font / None
Off / 0.5h / 1h / 8h
121.5 / LED+121.5 / LED
Alrt Off / Beep / LED /Beep+LED
°F / °C
Off / On
[32.0 °F (0 °C)] – [230.0 °F (110 °C)] ([122.0 °F (50 °C)])
Wide/Narrow
Off / On
[–22.8 °F (–12.7 °C)] – [+22.8 °F (+12.7 °C)] ([0 °F (50 °C)])
Off / On
Function
Enables/Disables the Scan lamp while paused during scanning.
Selects the Display illumination Mode.
Selects the frequency display between the “Large Character” and “Small Character” modes.
Setting of the display contrast.
Setting of the display brightness level.
Selects the S- & TX PO meter symbol.
Selects the display of the sensor units’ information.
Edits the BUSY indicator color.
Edits the TX indicator color.
Edits the Emergency lamp color.
Edits the Weather Alert lamp color.
Edits the Over Heating lamp color.
Select the Keypad beeper tone.
Enables/disables the Bell Ringer function.
Selects the Power-on beep.
Sets the Squelch threshold level for the AM and FM modes.
Sets the Squelch threshold level for the FM BC Band.
Selects the Scan Resume mode.
Selects the Dual Watch/Priority Function.
Selects the Receive-mode Battery Saver “sleep” ratio.
Setting of the synthesizer steps.
Selects the Priority Checking Time.
Selects the visible bandwidth of the Spectrum Analyzer.
Selects the Tone Decoder mode.
Setting of the CTCSS Tone Frequency.
Setting of the DCS Code.
Setting of the Time-Out Timer Countdown Time.
Selects the Control Locking lockout combination.
Selects the primary [121.5(HOME)] key function
Programming the [USER] key assignment (momentary-press mode).
Programming the [USER] key (press and holding) assignment.
Selects the Auto Power Off time (time before power goes off).
Selects the Emergency feature.
Selects the Alert functions when receiving the Weather Alert Signal on the WX Channel.
Selects the measurement units for the Temperature sensor.
Enables/Disables the Over-Heating Alarm.
Program the threshold temperature for the “High-Temperature” indicator.
Selects the receiving bandwidth on the BRS Band.
Internal Microphone On/Off.
Correcting the Thermometer setting.
CPU Clock Shift.
1. Scan Lamp
2. Backlight
3. Large Font
4. Contrast
5. Dimmer
6. Meter Symbol
7. Display Mode
8. RX LED
9. TX LED
10. EMG LED
11. Alert LED
12. TEMP LED
1. Beeper
2. Bell
3. PowerOn Beep
1. SQL
2. FM Radio SQL
3.Resume
4. DW/PRI
5. RX Save
6. Step
7. PRI Time
8. SPECT Width
9. SQL Type
10. TONE Set
11. DCS Set
1. T.O.T
1. Lock Mode
2. [121.5]
3. USER 1
4. USER 2
1. APO
2. Emergency
3. WX Alert
4. TEMP Unit
5. TEMP Check
6. TEMP Set
7. Bandwidth
1. Internal MIC
2. TEMP Offset
3. Clock Shift
Set Mode Item
1. Display
2. Sound
3. Receive
4. Transmit
5. Key Set
6. Misc. Setup
7. Option