A s s e m b l y

G u i d e

E1500

 

UPRIGHT FITNESS BIKE

S T E P 1

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:

Front Support

Tube

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.

If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

S T E P 1 ORANGE BAG

Position the front support tube in place under the mounting plate on the front side of the bike. Insert two bolts (M8x20L) with lock washers (SW8) and arc washers (M8x18x1.5T) into the holes. Tighten with the 5mm L-shaped wrench.

S T E P 2

BLUE BAG

Seat Post

 

 

 

 

Stud

Slide the rear foot into place on the frame. Insert two bolts (M8x25L) with two lock washers (SW8) to the outside holes. Insert two bolts (M8x70L) with

two lock washers (SW8) to the inside

Seat Post

S T E P 4

holes. Tighten all bolts with the 5mm

 

T-Shaped wrench.

 

 

Rear Foot

S T E P 2

SIMPLE

DELUXE

PREMIER

CONSOLES

Console

S T E P 3

PINK BAG

Slide the console mast cover onto the console mast.

Wrap the wire tie that exits the bottom of the console mast around the end of the console cable that is resting in the console mast mounting bracket. Pull the wire tie with the wire harness up through the console mast. Slide the console mast over the console mast mounting bracket. Insert three bolts (M8x15L) with three lock washers (SW8) to each side of the mast. Insert a set screw (M8x10L) to the front side of the mast and tighten with the 4mm L-Shaped wrench. Tighten all other bolts with the 5mm T-Shaped wrench. Slide the console mast cover down so that it sits in place on the bike.

Slide the heart rate wires from the handlebar through the hole in the handlebar mounting bracket on the console mast. Pull the wires completely through the hole and set the handlebars into place on the bracket. Secure the handlebars in place with the two bolts (M8x20L) and two lock washers (SW8). Tighten with the 5mm T-Shaped wrench.

Remove the four bolts from the back side of the console. Plug the console cable and heart rate wires into the back side of the console. Place the console onto the mounting plate of the console mast and re-insert the four mounting bolt. Tighten with the screwdriver.

Remove the two bolts from the backside of the console mast. Attach the water bottle cage to the mast with these two bolts. Tighten with the screwdriver. Insert water bottle.

Heart Rate

Wires

Adjustment Knob

S T E P 3

Wire Harness

S T E P 4

Console Mast

Console Mast

Cover

SEAT & PEDALS

• Slide the seat onto the seat post

S T E P 5

CONSOLE

 

stud. Tighten the 14mm nuts on the

 

 

 

 

 

bottom side of the seat to secure in

• Refer

to

Product Selection

and

place.

Model

Configuration

decal

on

 

• Slide the seat post into the frame

console or follow these steps.

 

seat post bracket.

• Once the product is plugged in turn

 

• Insert the adjustment knob through

on the console

 

 

 

 

 

 

 

the seat post bracket and turn to tighten.

• Select product (Bike (BK) or Elliptical

• Attach left and right pedal straps to

(EP)) using the resistance arrow keys.

Press ENTER to select.

 

 

left and right pedals.

 

 

• Select model number (Bike (1500,

• Attach left and right pedals to left

2050, 2250, 3200) or Elliptical

and right crank arms. NOTE: both

(1500, 6000, 6200)) using the

pedals and crank arms should be

RESISTANCE

arrow

keys.

Press

labeled left or right. Tighten with the

ENTER to select. Console will reset to

included pedal wrench.

start-up screen.

 

 

• Plug in power supply to power

• The product selection and model

socket on the front side of the bike.

configuration is now complete.

 

Page 3
Image 3
Vision Fitness E1500 manual E P 1 Orange BAG, Seat & Pedals, Console