A s s e m b l y
G u i d e
R2050 AND R2150
STEP-THRU SEMI-RECUMBENT FITNESS BIKES
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
S T E P 1 | ORANGE BAG | Rear Foot |
S T E P 4
Rear Foot
Joint Cover
S T E P 3 | PINK BAG |
• Slide the console mast cover onto |
the console mast. |
• Take the wire tie that exits the |
bottom of the console mast and wrap |
it around the wire harness and heart |
rate wires that are sitting in the |
console mast bracket on the frame. |
Pull the wire tie up through the top of |
the console mast so that the wire |
harness and heart rate wires exit the |
top of the mast. |
• Slide the bottom of the console mast |
over the frame bracket being careful |
not to pinch the heart rate wires or |
wire harness. Assure the mast is |
positioned correctly by inserting the |
Set Screw (M8x10L) through the front |
edge of the mast. Tighten with the |
5mm |
mast to the frame with four bolts |
(M8x15L) and four lock washers (SW8). |
Tighten with the 5mm |
• Slide the console mast cover down |
so it sits on the frame covers. |
• Mount the console mast handlebar |
to the console mast with two bolts |
(M8x20L) and two lock washers (SW8). |
Tighten with the 5mm |
• With the screwdriver remove the |
•Slide the Rear Foot into place on the back end of the frame. Secure the foot in place to the frame with two bolts (M8x20L) and two lock washers (SW8) to the outside holes and with two bolts (M8x65L) and two lock washers (SW8) to the inside holes. Tighten with the 5mm
•Attach each half of the rear foot joint cover with the M4x10L screw. Tighten with the screwdriver.
S T E P 2 | BLUE BAG |
•Rotate the handle on the seat frame to the forward most position. Tighten the adjustment bolt on the seat frame bracket with the 5mm
•Slide the seat frame onto the seat rail. Attach the seat rail stopper onto the seat rail with two (M8x25L) bolts and two lock washers (SW8). Tighten with the 5mm
•Connect the heart rate wires in the seat handlebar to the heart rate wires coming up from the seat frame.
•Mount the seat handlebars to the seat frame with four bolts (M8x15L) and four lock washers (SW8). Tighten with the 5mm
•Mount the seat bottom cushion to the seat frame with four bolts (M6x35L) and four arc washers (M6). Tighten with the 4mm
•Mount the seatback cushion to the seat frame with four bolts (M6x35L) and four arc washers (M6). Tighten with the 4mm
S T E P 1
Seat Frame
Adjustment Bolt
S T E P 2
S T E P 3
Console Mast
Cover
Console Mast
Bracket
Seat Rail
Stopper
four bolts on the back side of the |
console. Plug in the wire harness and |
heart rate wires to the back side of the |
console. Mount the console to the |
console mast with the four bolts and |
screwdriver. |
• Remove the water bottle cage bolts |
from the backside of the console mast. |
Mount the water bottle cage to the |
mast with these two bolts and the |
screwdriver. |
S T E P 4 | PEDALS |
•Attach the left and right pedals to the left and right crank arms. N O T E : both pedals and crank arms should be labeled left or right. Tighten with the included pedal wrench.
•Plug in the power supply to the power socket on the front side of the bike.
Console Mast
Water Bottle
Cage
