GETTING STARTED

 

 

 

WALL MOUNTING

 

 

AC ELECTRICAL

OUTLET

wooden stud

wallboard

TONE

PULSE

TONE PULSE

Setting Up Your VTECH 910 ADL

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the rear of the base unit. Plug the other end into a telephone wall jack. Make sure the plugs snap securely into place.

3.Plug the AC power adapter into an electrical outlet and the DC connector to the back of the base unit.

CAUTION:Use only the AC adapter shipped with your 910ADL. This is a Class 2 AC adapter, specifically designed for use with the 910 ADL.

NOTE: Connect power to the base unit before placing the handset in the cradle.

4.Set the TONE/PULSE switch on the base unit. If you have touch tone service on your phone line, set the switch to TONE. If you have rotary service, set the switch to PULSE.

TELEPHONE

WALL JACK

5.CHARGE THE HANDSET BATTERIES BEFORE USE. The batteries recharge automatically whenever the handset is in the base unit cradle. The batteries must be charged for 24 hours before using your phone for the first time.

6.CHECK FOR A DIAL TONE. After the batteries are charged, pick up the handset and press the PHONE key. The

PHONE indicator should light up, and you should hear a dial tone. If not, see IN

CASE OF DIFFICULTY.

CAUTION:

1.Never install telephone wiring during a lightning storm.

2.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

1.Choose a spot near an electrical outlet and a telephone jack.Your

phone requires a modular telephone jack and a standard electrical outlet (120v AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the base. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.

2.Position the wall mount adapter on the base. Line up the tabs on the wall mount adapter with the holes on the bottom of the base. Snap the wall mount adapter firmly in place.

3.Mount the base on the wall. Position the base so the mounting studs will fit into the holes on the bottom of the base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the base down on the mounting studs until it locks into place.

4.Connect the telephone cord. The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the base. Insert the other end of the plug into the wall jack.

5.Connect the power cord. Plug the DC connector into the DC jack at the rear of the base unit. Plug the AC power adapter into an electrical outlet.

6.Set the dial mode switch on the base unit. If you have touch tone service on

your phone line, set the switch to

TONE. If you have rotary service, set

the switch to PULSE.

HANDSET FEATURES

BASE UNIT FEATURES

IN USE LED

 

 

LOW

BATT LOW LED

 

IN USE

 

BATT

 

VOLUME SWITCH

PHONE

CHAN

OF

OFF KEY

 

 

 

F

 

PHONE KEY/

1

2 ABC

3 DEF

CHAN KEY

FLASH KEY

 

 

 

 

 

 

4 GHI

5 JKL

6 MNO

 

 

7PQRS

8 TUV

9WXYZ

 

TONE/ KEY

TONE

0OPER

#

MEM KEY

PROG KEY

 

 

 

PROG

MEM

REDIAL

REDIAL KEY

CHARGE LED

*T h e C H A R G E L E D illuminates steadily when the handset is in the base cradle to indicate that the handset battery is being charged.

SPARE BATT LED

IN USE LED

* Immediately after placing the handset in

the base cradle, the IN USE LED flashes

to indicate that the initialization (assigning

a new security code and channel) is in

progress

* The IN USE LED will stop flashing and light

off when the initialization is complete.

* The IN USE LED illuminates whenever the

handset is being used.

* This LED also flashes with the cadence of

the incoming ring.

POWER LED

IN USE LED

*The IN USE LED lights when the phone line is being used by the handset.

*It flashes in cadence with an incoming ring.

*It flashes quickly during PROG mode.

BATT LOW LED

*The BATT LOW LED will flash when the

MEM KEY

*Press the MEM key to enter MEMORY mode.

*The sequence for dialing out a speed dial

number in memory is: PHONE, MEM, Number Button (0-9).

PROG KEY

* Press PROG key to enter PROGRAM

*The SPARE BATT LED illuminates steadily

w h e n a b a t t e r y i s placed in the base unit charge cradle.

* The POWER LED illuminates when the

base power adapter is plugged in and

power is applied to the base unit.

handset battery is getting low and needs to be recharged.

PHONE KEY/ FLASH KEY

*Press the PHONE key to make a call.

*If you are currently on a call, pressing

PHONE flashes the line. This would be used with a feature like call waiting to answer your second call.

CHAN KEY

*Pressing the CHAN key when the handset is in use will activate a channel change to the next free channel.

*This is used if you are experiencing

noise or interface on the current channel.

OFF KEY

*Press the OFF key to exit all modes of operation.

mode. See Programming Speed Dial

Numbers for more details.

REDIAL KEY

*When you hear the dial tone, pressing the REDIAL key will dial out the last number that was called on your phone.

*It can also be used to store the last

number dialed into the speed dial memory. See Storing a Redial Number into Speed Dial for details.

TONE/* KEY

*In PULSE dialing mode, this key is used to switch to Temporary TONE dialing mode.

VOLUME SWITCH

*Slide switch UP for High Volume (H) setting.

*Slide switch DOWN for Low Volume (L) setting.

 

MEMORY

 

 

 

 

DIALING

 

 

 

 

•

 

 

 

 

•

 

 

 

 

•

 

 

 

•

•

 

 

 

•

 

 

 

 

•

 

 

 

 

•

 

IN POWER

 

•

 

 

•

 

 

 

 

 

CHARGE

USE

 

SPARE

 

 

BATT

 

 

 

 

 

 

 

PAGE

 

 

 

TONE/PULSE SWITCH

 

 

 

PAGE KEY

* This switch will switch the phone

 

* Press the PAGE key to page the

between TONE dialing and PULSE

 

handset.

dialing.

 

 

 

* Press it a second time to cancel a page.

 

 

 

 

* The base will ring the handset 4 times before ending the page automatically.

* The handset can also cancel the page by pressing the OFF key.

Page 1 Page 3
Page 2
Image 2
VTech 910, 915 important safety instructions Getting Started Wall Mounting, Handset Features Base Unit Features
Page 1 Page 3

910, 915 specifications

The VTech 915,910 is a cutting-edge communication device designed for both personal and professional use, seamlessly combining advanced technology with user-friendly features. This state-of-the-art cordless phone system is ideal for those seeking reliable connectivity and exceptional sound quality.

One of the standout features of the VTech 915,910 is its DECT 6.0 technology. This technology ensures a crystal-clear sound quality while reducing interference from other wireless devices. DECT (Digital Enhanced Cordless Telecommunications) provides a secured line with minimal eavesdropping risk, making it perfect for private conversations.

The phone system typically supports multiple handsets, allowing users to expand their communication capabilities throughout their home or office. Each additional handset is easy to install and sync, making it a flexible solution for growing communication needs. Users can enjoy the convenience of intercom features, call transfer, and paging capabilities among handsets.

Another notable characteristic of the VTech 915,910 is its large backlit display. The bright display makes it easy to read caller ID, call logs, and menu options, even in low-light conditions. Additionally, the phone is equipped with a speakerphone feature that provides hands-free communication, allowing users to multitask while engaged in a call.

The VTech 915,910 also focuses on user convenience with options such as a built-in answering machine. This feature allows users to receive messages even when they are away from their phone, and it provides customized greeting options to enhance the caller experience. Moreover, the phone includes a call block feature, enabling users to reject unwanted calls easily.

With its long-lasting battery life, the VTech 915,910 ensures that users can stay connected without worrying about frequent recharging. The eco-friendly design also reduces energy consumption, making it an environmentally responsible choice.

Lastly, the VTech 915,910 is designed with ergonomic considerations, ensuring it fits comfortably in hand for prolonged use. Its sleek and modern design makes it an attractive addition to any home or office setup, combining functionality with aesthetic appeal.

In conclusion, the VTech 915,910 is an exceptional cordless phone system, equipped with advanced technologies and user-centric features, promising reliability and efficiency in communication for all users.
Top Page Image Contents