VTech 9119 Gettting Started, Handset Features Wall Mounting, Base Unit Features

GETTTING STARTED

Setting Up Your VT9119

1.Choose an area near an electrical outlet and a telephone wall jack.

2.Plug the AC power adapter into an electrical outlet and the DC connector to the back of the base unit.

CAUTION: Use only the AC adapter shipped with your VT9119. It is specifically designed for this product.

NOTE: Connect power to the base unit before placing the handset in the cradle.

3.CHARGETHE HANDSET BATTERY PACK BEFORE USE. The batteries recharge automatically whenever the handset is in the base unit cradle. The batteries must be charged for 16 hours before using your phone for the first time.

4.Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the rear of the base unit. Plug the other end into a telephone wall jack. Make sure the plugs snap securely into place.

5.CHECK FOR A DIAL TONE. After the batteries are charged, pick up the handset and press the PHONE key. The IN USE indicator should light up, and you should hear a dial tone. If not, see IN CASE OF DIFFICULTY.

CAUTION:

1.Never install telephone wiring during a lightning storm.

2.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

4.Use caution when installing or modifying telephone lines.

4

HANDSET FEATURES

WALL MOUNTING

1.Choose a spot near an electrical outlet and a telephone jack.Your phone requires a modular telephone jack and a standard electrical outlet (120V AC). The power cord is six feet long; make sure there is an electrical outlet within reach of the base. The outlet should not be controlled by a wall switch. If the switch is ever turned off, the phone will not operate.

2.Mount the base on the wall. Position the base so the mounting studs will fit into the holes at the back of the base. Position the power cord to extend down the wall the phone is to be mounted on. Slide the base down on the mounting studs until it locks into place.

3.Connect the telephone cord. The telephone line cord has a snap-in plug at each end. Insert one of the plugs into the jack on the bottom of the base. Insert the other end of the plug into the wall jack.

4.Connect the power cord. Plug the DC connector into the DC jack at the rear of the base unit. Plug the AC power adapter into an electrical outlet.

5

BASE UNIT FEATURES

PHONE LED

•The PHONE LED lights when the handset is on an active call.

•It flashes in cadence with an incoming ring.

•It flashes quickly during PROG mode.

•It flashes slowly when battery is low.

PHONE KEY/ FLASH KEY

•Press the PHONE key to make a call.

•If you are currently on a call, pressing PHONE flashes the line.This would be used with a feature like call waiting to answer

your second call.

PROG KEY

•Press PROG key to enter PROGRAM mode. See Programming Speed Dial

Numbers for more details.

VOLUME CONTROL

•Ajust volume of what you hear through the handset.

6

•While on a call, press the Up or Down key to adjust the listening volume.The Handset will emit a double beep when the maximum or minimum volume level has been

reached.

OFF KEY

•Press the OFF key to exit all modes of

operation.

REDIAL / PAUSE KEY

•When you hear the dial tone, pressing the REDIAL key will dial out the last number that wascalled on your phone.

•It can also be used to store the last number dialed into the speed dial memory. See

Storing a Redial Number into Speed Dial for details.

•You can store a PAUSE into your dialing number. See Storing Pauses in Memory

for detail.

CHAN KEY

•Pressing the CHAN key when the handset is in use will activate a channel change to the next free channel.

•This is used if you are experiencing noise

or interference on the current channel.

MEM KEY

•Press the MEM key to enter MEMORY mode.

•The sequence for dialing out a speed dial number in memory is: PHONE, MEM,

Number Button (0-9).

TONE/ * KEY

•In PULSE dialing mode, this key is used to switch to Temporary TONE dialing mode.

IN USE/CHARGE LED

•The LED illuminates steadily when the handset is in the base cradle to indicate that the handset battery is being charged.

•The LED illuminates whenever the handset is being used.

•This LED also flashes with the cadence of

the incoming ring.

PAGE KEY

•Press the PAGE key to page the handset.

•Press it second time to cancel a page.

•The base will ring the handset 1 minute before ending the page automatically.

•The handset can also cancel the page by pressing the OFF key.

7

CUT

CUT

REPLACEMENT BATTERY ORDER FORM

For VT 9119 Cordless Telephone

Name:

Adress:

City:

State:

Zip:

Daytime Phone Number: (

)

ORDER INFORMATION

For Model VT 9119

(QTY.) Batteries @$19.95 each

$

Shipping/Handling @$ 4.95 per battery

$

METHOD OF PAYMENT: DO NOT SEND CASH

CHECK/M.O.

VISA

MASTERCARD

DISCOVER

AMERICAN EXPRESS

Credit Card#

EXP. DATE

CARD HOLDER’S SIGNATURE

PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:

VTECH COMMUNICATIONS INC. 8770 SW NIMBUS AVENUE

BEAVERTON, OREGON 97008-7195 USA

YOU MAY ALSO ORDER BY PHONE.CALL 1-800-595-9511