Waterpik Technologies B002BSH2DM warranty Functions & Set up of HF3 IP’s Amplifier

User’s Manual

Subwoofer High Force 3 Ice Power

We thank you very much for purchasing a Waterfall High Force Subwoofer. Our deliberate choice for aesthetics and performance is constantly guiding our research and development towards innovative technologies. In order to achieve the best performance with your Home Cinema system, we recommend you read carefully the following set up instructions.

In order to achieve the best acoustical performance, the HF3 IP Evo, ideally has to be positioned near an angle/corner in the room.

A) Functions & Set up of HF3 IP’s Amplifier

Warning :

Check the mains voltage selector (N°1) position (115V/230V) and use the correct voltage for your country before connecting the mains plug. Changing the fuse : In the event of complete failure, first disconnect the powers cable from the mains, then check the mains fuse. When replacing the fuse, only use a fuse which is absolutely identical to the original one. If this does not solve the problem, contact your dealer.

•Only the subwoofer is to be connected to the mains supply. Never plug your speakers directly into the main power supply.

•Before proceeding with any connection, make sure that all your equipment is switched off.

•Before switching it on, please ensure that the "level" button (N°4) is on minimum.

• Your Waterfall Speakers are to be directly connected to the speaker output socket on your amplifier or A/VProcessor.

•Also ensure that the polarities are correct : + ( red ) and - ( black ).

•Do not expose this product to heat and humidity.

13	10	9	8	7	6	5	4	Control panel
DIRECT 1	VENTED	12dB	AUTO	OFF	FREQ	PHASE	LEVEL
DIRECT SUB	FULL CLOSED	LFE 24dB ON
					40 Hz 150	0° 180°	0 MAX
				LOW LEVEL INPUT

1	Mains voltage selector (115V/230V)
2	Fuse
3	Main power switch (on - off)
4	Level :Volume adjustment of the integrated amplifier.
5	Phase :Alows you to adjust phase from 0 to 180°.
6	Freq :Adjustment of the frequency cut off, from 40 to 150Hz.

11

			Mains cord
L	R	DIRECT 1	(supplied)
		DIRECT 2
	+

7 PRT : Standby LED indicates unit in standby mode with power connec-

ted.When the Sub is activated this standby LED is off and the Logo LED

lights up. Flashes in case of default.

S300

12

-
HI-LEVEL INPUT	14
SUBWOOFER

8 On – Auto – Off : Recommended Setting should be : "Auto", so when

not in use for a while, amplifier goes back into standby, if "On" position

is used, this means the amplifier will continuously be on, and will not go

ATOHM®

	3			Main power
				switch
	OFF O I	ON		(on - off)
DO NOT OPEN / NE PAS OUVRIR	1			2
RISK OF ELECTRIC SHOCK				Fuse
DANGER D'ELECTROCUTION	115V/60Hz 360W		115V : FUSE T3.15AL
	230V/50Hz T 360W		230V : FUSE T1.60AL

DESIGNED IN FRANCE / TECHNOLOGIE FRANÇAISE

The subwoofer MUST be connected to the mains with the enclosed connector cord.The main switch has to be on "on" position and the (N°8) switch "on-auto-off" in the "auto" position.Your HF3 IP Subwoofer is equipped with a wide range of connection options for Hi Fi or Audi Video, Home Cinema.

into standby.

9 24-12-LFE : Switching of the active filter of the Sub.The choice of 24Db

per octave or 12Db per octave is to be determined through listening

and personal choice.

10Factory settings. DO NOT CHANGE.

11Low Level Input/Output :The "audio" signals are transmitted by a cinch cable (supplied by our retailer) linking the "subwoofer Pre-out" of the processor to one of the "Line in" of the Sub, (either white or red entry).

12"High Level Input" :To be used only with conventional stereo amplifiers.

13Input selector (for specific set up).

14Connections for specific use.

www.waterfallaudio.com