Manuals / Wayne-Dalton / Household Appliance / Garage Door Opener

Wayne-Dalton 3014, 3012 Idrive models 3660-372, 3661-372, 3662-372, 3760-372, Torsion idrive

Models: 3750-372 3651-372 3012 3014

1 7
Download 7 pages 63.46 Kb
Page 5
Image 5

Step 2: Photoelectric Safety Sensor Wiring Installation For:

idrive™ models: 3660-372, 3661-372, 3662-372, 3760-372, 3751-372.

Uncoil wires from photoelectric sensors and route wires up garage wall and along door header towards the right side of the opener (see Fig. 3 ). Route wires behind torque tube and tack wires in place with insulated staples (not supplied).Take care to run wires in a location where they will not interfere with the operation of the door and do not staple through wire. Connect photoelectric sensors to the opener terminal block on right side of the opener. Separate wire ends and strip about 1/2” of insulation off each of the wire ends. Insert a 3/32” (2.5mm) max. width flathead screwdriver into the lower hole #1 of the terminal block. Twist screwdriver to open wire clamp in upper hole #1 of terminal block. Insert both sender and receiver solid white wires into upper hole #1 until the wires bottom out and release screwdriver tension. Insert both sender and receiver wires (white with black stripe) into upper hole #2 by the same process on lower hole #2 of terminal block. Be sure to observe polarity. Once wires are connected, install jumper on to the left most set of pins labeled “PE” of the opener.

IMPORTANT! Keep sender/receiver wires away from moving members. Pull on external wires to test for secure connection. Check that the wires are stapled in place and staples have not cut wire insulation. Reconnect the power to the garage door opener. Proceed to Step 3.

Torsion idrive™ models: 3651-372, 3750-372.

To locate the terminal block for the infrared sensor sender/receiver wires, you must first move the right hand gear assembly. Loosen the set screw and slide the gear assembly away from the opener. Uncoil wires from photoelectric sensors and route wires up garage wall and along door header towards the right side of the opener (see Fig. 4). Route wires behind torque tube and tack wires in place with insulated staples (not supplied).

Connect photoelectric sensors to the opener terminal block on right side of the opener. Separate wire ends and strip about 1/2” of insulation off each of the wire ends. Insert a 3/32” (2.5mm) max. width flathead screwdriver into the upper hole #1 of terminal block. Twist screwdriver to open wire clamp in lower hole #1 of terminal block. Insert both sender and receiver solid white wires into lower hole #1 until the wires bottom out and then release screwdriver tension. Insert both sender and receiver wires (white with black stripe) into lower hole #2 by the same process. Be sure to observe polarity. Keep the sender and receiver wires straight and organized by wrapping them around the backside of the opener and securing them using the cord clip (adhesive backed) provided.(Insure the surface the cord clip is attached to is clean and oil free.

IMPORTANT! Keep sender/receiver wires away from moving members. Pull on external wires to test for secure connection. Check that the wires are stapled in place and staples have not cut wire insulation. Reconnect the power to the garage door opener. NOTE: Reinstall the right hand gear assembly onto the drive gear. Ensure that the gear assembly is installed correctly. Proceed to Step 3.

FIG. 3 Wire Routing

Insert wires

Jumper

into upper

hole #1

Insert wires installed

 

into upper

 

hole #2

 

Jumper

 

Insert screw

Insert screw

Pins

driver into lower

driver into

hole #2

labeled

lower hole #1

“PE”

White wires with black stripe

Solid white wires

idrive™

FIG. 4 Wire Routing

Right hand gear assembly

Insert screwdriver into upper holes

Set screw

Insert wires

Cord clip

into lower holes

 

Torsion idrive™

5

Page 4 Page 6
Page 5
Image 5
Wayne-Dalton 3014, 3012, 3750-372 Idrive models 3660-372, 3661-372, 3662-372, 3760-372, Torsion idrive models 3651-372
Page 4 Page 6

3750-372, 3651-372, 3012, 3014 specifications

Wayne-Dalton is a renowned manufacturer in the garage door industry, offering a wide range of products that cater to various needs. Among their most notable models are the Wayne-Dalton 3014, 3012, 3651-372, and 3750-372 garage doors. Each model brings unique features and technologies designed for durability, aesthetics, and functionality.

The Wayne-Dalton 3014 model is characterized by its exceptional durability and design versatility. It features a steel construction that promotes long-lasting performance, ensuring it can withstand the rigors of everyday use. The door is available in a variety of colors and finishes, allowing homeowners to find the perfect match for their home’s exterior. Additionally, it comes equipped with insulation options that enhance energy efficiency, helping to keep garages comfortable year-round.

The Wayne-Dalton 3012 model emphasizes simplicity and reliability. With a classic design that pairs well with traditional architecture, this model is perfect for homeowners seeking a timeless look. It also features sturdy construction materials that provide added security against potential intrusions. The 3012 model is designed with low maintenance in mind, making it an excellent choice for those who prefer functionality without the hassle.

The 3651-372 model takes performance to the next level. It is constructed with advanced materials that ensure superior strength and insulation properties. This model is particularly beneficial for homes in areas with extreme weather conditions. It also includes modern technology such as smart garage door openers, enabling homeowners to control their garage doors remotely via mobile apps, thus enhancing convenience and security.

Lastly, the Wayne-Dalton 3750-372 model features over-head door technology that enhances its efficiency and reliability. This model incorporates a multi-layer construction approach, combining steel, insulation, and a wood appearance vinyl overlay. This not only offers aesthetic appeal but also provides exceptional insulation, keeping the garage temperature stable. The 3750-372 model can also be customized with various windows and decorative hardware options, allowing homeowners to personalize their garage doors to suit their style.

In summary, Wayne-Dalton's range of models, including the 3014, 3012, 3651-372, and 3750-372, exemplifies quality craftsmanship, advanced technology, and customizable features. These models cater to a variety of preferences, ensuring that there’s a perfect garage door solution for every homeowner.