Wayne-Dalton 900 specifications Series Rolling Service Doors, O R S, Part 1 General

flat include will doors Tite

-

Bar/Extr

1

900 SERIES ROLLING SERVICE DOORS

For easier door specifications or product questions call the WayneTec Consulting Service 1-800-764-1457.

to Designed

.

bearings ball sealed

as

Model

900 SERIES ROLLING SERVICE DOORS

GENERAL SPECIFICATIONS FOR ROLLING SERVICE

D O O R S

Note to Specifiers:

Words in parentheses indicate frequently specified and highly recommended options.

PART 1 GENERAL

1.01Work Included—The opening will be equipped with Wayne- Dalton 900 Series rolling doors,

_____

manufactured by Wayne-Dalton Corp.

1.02Related Work—Opening preparation, miscellaneous or structural metal work, access panels, finish or field painting, field electrical wiring, wire, conduit, fuses, and disconnect switches are in the Scope of Work of other divisions or trades.

PART 2 PRODUCT

2.01Curtain will be composed of prime painted galvanized steel interlocking slats (A) gauge, No.

(B) slats, roll-formed from (C) per ASTM standards and designed to withstand a 20 PSF windload.

Ends of alternate slats will be fitted with metal endlocks/windlocks.

Bottom Bar will consist of 2 equal galvanized steel (stainless steel) angles, (aluminum extrusion) minimum 1¼ 8"thick,to stiffen curtain with neoprene loop astragal. When required for additional security, provide (slide bolts) (cylinder locks) on the bottom bar operable from (coil side) (opposite coil side) (both sides).

2.02Guides will be of roll-formed galvanized steel channels and angles (three angle assembly) of steel (stainless steel) (aluminum) to form a slot of sufficient depth to retain curtains in guides to resist 20 PSF windload. Guides may be provided with integral windlock bars and removable bottom bar stops.

2.03Brackets will be of galvanized steel plates with permanently

enclose ends of coil and provide support for counterbalance pipe at each end.

2.04Counterbalance: Curtain to be coiled on a pipe of sufficient size to carry door load with deflection not to exceed .03 inches per foot of door span and to be evenly balanced by helical springs, oil tempered torsion type designed with a 25% safety factor. Cast iron barrel plugs will be used to anchor springs to tension shaft and pipe.

2.05Hood will be minimum 24 gauge (prime painted galvanized) (galvanized) (slatted) steel, flanged at top for attachment to header and flanged at bottom to provide longitudinal stiffness. Hood will enclose curtain coil and counterbalance mechanism.

2.06Finish: Shop coat of rust inhibitive primer on non-galvanized surfaces and operating mechanisms. Aluminum finish to be (mill) (204R1 clear anodized) (bronze anodized). Stainless steel finish to be (#4). Curtain will be (white) (blue) (gray) (tan) (brown).

2.07Operation: Door will be

operated by means of (manual, push-up) (chain hoist with gear drive reduction) (awning crank) (wall crank box) (motor operation). (Electrical) (Pneumatic) sensing edge to be attached to bottom bar to (stop) (stop and reverse) the door when it contacts an object during the closing cycle.

2.08Weatherstripping: Air-

slats, bottom astragal, exterior surface guide weatherstrip, and internal hood baffle weatherstrip.

2.09Locking: (Manual push-up doors will have interior slide-bolts suitable for padlocks by others.) (Chain-hoist door will have chain keepers suitable for padlocks by others.) (Electric-motor operation doors will lock through the operator gearing.) (Cylinder locks can be provided with the doors.)

CAUTION: When specifying cylinder locks on electric-motor operated doors, electric interlocks should also be specified to prevent operation when lock bolts are engaged in the guides, thus preventing damage to the curtain and/or operator.

PART 3 EXECUTION

3.01Install the doors in accordance with Wayne-Dalton Corp. instructions and standards. Installation and maintenance will be by an authorized Wayne-Dalton representative.

Because of continuing product improvements, we reserve the right to change the product specifications and designs without prior notice.

COLORS INCLUDE: (22 and 24 gauge only)

White

Blue

Gray

Tan

Brown

WAYNE-DALTON CORP. • ONE D O O R DRIVE • MT. HOPE, OH 44660 • PH. 800-764-1457 • FX. 800-336- 1422

©2001 Wayne-Dalton Corp. Rev. 11/01 246570