Flag angle
Vertical | 5/16” x |
track | |
assembly | Lag screws |
Jamb |
|
bracket |
|
Bottom | Track |
section | rollers |
12R FA 15R FA 12R QI 15R QI
Flag angle lag screw locations | ||
3/8” to 5/8” |
| |
Spacing |
| |
Bottom section |
| |
Vertical track | Track roller | |
Floor | ||
|
9 | Top Fixtures | |
Tools: Power drill, 7/16” Socket driver | ||
|
Remove, but retain
Slide the top fixture assembly between the strut and section. Align the edge of the top fixture parallel to the top section edge. Secure the top fixture and strut to the top section with (3) 1/4”- 20 x 7/8” self drilling screws through the upper and lower slots of the top fixture. Finish
Top | Strut | Short stem |
section | ||
|
| track roller |
|
| Top fixture |
|
| base |
| (3) |
|
| Self drilling screws |
|
|
| End cap |
8 | Stacking Sections | |
Tools: Power drill,7/16” Socket driver | ||
|
Note: The sections can be identified by the graduation of the factory installed end hinges. The smallest graduated end hinge on section should be stacked on top of the bottom section, with each graduated end hinge increasing as the sections are stacked, see Parts Breakdown on page 2.
Note: Make sure graduated end and center hinges are flipped down, when stacking another section on top.
Note: Larger doors will use long stem track rollers with double graduated end hinges. Place track rollers into graduated end hinges of remaining sections.
With assistance, lift second section and guide the track rollers into the vertical tracks. Lower section until it is seated against bottom section. Align vertical marks in the upper alignment sticker, with the lower alignment sticker on right hand side, on the back of door. Keep sec- tions aligned and fasten center hinge(s) first; then end hinges last using
NOTE: To prevent center hinge leaf(s) from rotating, first secure the top middle hole of the center hinge leaf with one 1/4” – 14 x 5/8”
NOTE: Larger doors with double graduated end hinges, fasten both hinges to connect the sections using 1/4” - 14 x 5/8”
Repeat same process for other sections, except top section.
10 | Drawbar Operator Bracket | |
Tools: Power drill, 7/16” Socket driver | ||
|
Note: If you’re installing a drawbar operator, the drawbar operator bracket must be mounted and secured prior to installing top section.
Important: when connecting a drawbar operator type garage door opener to this door, a
Remove, but retain
NOTE: For retro fit applications, the drawbar operator bracket must be aligned with an exist- ing drawbar operator.
Locate the center of the top section and slide drawbar operator bracket under strut till the drawbar operator bracket is seated against the strut flange.
NOTE: Prior to fastening drawbar operator bracket to top section, ensure the top edge of drawbar operator bracket is aligned with the top edge of the section, as shown.
Attach the drawbar operator bracket using (8) 1/4” – 20 x 11/16” self drilling screws (as shown). Finish
Important: Push & hold the hinge leafs securely against the sections while securing with
Top section
Strut
Top section
Drawbar operator bracket
Strut
Left double graduated
end hinge with long
stem track roller
Right double graduated
end hinge with long
stem track roller
Lock section | Alignment | |
sticker | ||
|
|
|
Vertical tracks
Alignment sticker
Secure top
middle hole first
Left graduated end hinge | Center | Right graduated end hinge | |
hinge(s) | |||
with short stem track roller | with short stem track roller |
1/4” - 20 x 7/8”
Drawbar operator | (8) 1/4” - 20 x 11/16” |
bracket in place | |
under strut |
|
Top Section
11 Tools: Hammer, Power drill, 7/16” Socket driver, 7/16” Socket, 7/16” Wrench, Ratchet wrench, Step ladder, Tape measure
Place the top section in the opening. Temporarily secure the top section by driving a nail into the header near the center of the door and bending it over the top section. Now, flip up the graduated end hinge and center hinge leaves, hold tight against section, and fasten center hinges first and end hinges last (refer to step, Stacking Sections). Vertical track alignment is critical. Position flag angle between
8
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at