Weber 89563 Sideburner Maintenance, Troubleshooting, Side Burner Maintenance, With aluminum foil

SIDEBURNER MAINTENANCE 31

SIDE BURNER MAINTENANCE

WARNING: All gas controls and supply valves should be in the “OFF” position.

Make sure black wire is connected between the igniter and electrode. Make sure white wire is connected between the igniter and grounding clip. Spark should be a white/blue color, not yellow.

1)Igniter Wire

2)Ground wire

3)Burner

(3)

(1)

(2)

Side Burner Grate

Side Burner cap

Side Burner Ring & Head

Igniter Electrode

Control Knob

Igniter

(1) (2)

TROUBLESHOOTING

PROBLEM	CHECK	CURE
Burners burn with a yellow or orange flame, in	Inspect Spider/Insect Screens for possible obstructions.	Clean Spider/Insect Screens. (See Section “Annual
conjunction with the smell of gas (This is normal	(Blockage of holes.)	Maintenance”)
for the burner lighting tube).
Symptoms:	The excess fl ow safety device, which is part of the	To reset the excess fl ow safety device turn all burner control
Burners do not light. -or- Burners have a small	barbecue to cylinder connection, may have activated.	knobs and the cylinder valve off. Disconnect the regulator
flickering flame in the “HI” position. -or-		from the cylinder. Turn burner control knobs to “HI”. Wait
Barbecue temperature only reaches 250˚ to 300˚		at least 1 minute. Turn burner control knobs to “OFF”.
in the “HI” position.		Reconnect the regulator to the cylinder. Turn cylinder valve
		on slowly. Refer to “Lighting Instructions”.
Burner does not light, or flame is low in “HI”	Is LP fuel low or empty?	Refi ll LP cylinder.
position.
	Is fuel hose bent or kinked?	Straighten fuel hose.
	Does Burner light with a match?	If you can light Burner with a match, then check the
		Crossover® ignition system.
	Did you use the snap igniter several times until the main	Make sure to hold the control knob in for two seconds after
	burner lit (See Lighting Instructions)?	snapping the igniter and seeing the orange fl ame from the
		burner lighting tube.
	Does the igniter work (Do you see a spark when you	Try manually lighting the burner (refer to “Main Burner
	repeatedly use the snap igniter?	Manual Lighting”). Call customer service.
Experiencing flare-ups:	Are you preheating barbecue in the prescribed manner?	All burners on HI for 10 to 15 minutes for preheating.
	Are the cooking grates and Flavorizer® bars heavily	Clean thoroughly. (See Section “Cleaning”)
	coated with burned-on grease?
CAUTION: Do not line the bottom tray	Is the bottom tray “dirty” and not allowing grease to fl ow	Clean bottom tray.
	into catch pan?
with aluminum foil.
Burner flame pattern is erratic. Flame is low when	Are burners clean?	Clean burners. (See Section “Maintenance”.)
burner is on “HI”. Flames do not run the whole
length of the burner tube.
Inside of lid appears to be “peeling.” (Resembles	The lid is porcelain enamel or stainless steel, not paint. It	Clean thoroughly. (See Section “Cleaning”.)
paint peeling.)	cannot “peel”. What you are seeing is baked on grease
	that has turned to carbon and is fl aking off.
	THIS IS NOT A DEFECT.
Cabinet doors are not aligned.	Check the adjustment pin on the bottom of each door.	Loosen adjustment nut/s. Slide door/s until aligned. Tighten
		nut.

If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com®.

WWW.WEBER.COM®