SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 17

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instruc- tions.

19

Page 19
Image 19
Weed Eater 186073 manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

186073 specifications

The Weed Eater 186073 is a notable addition to the world of outdoor power equipment, designed specifically for homeowners and gardening enthusiasts who value efficiency and ease of use. This electric string trimmer combines innovative features and cutting-edge technology to provide an exceptional lawn care experience.

One of the standout features of the Weed Eater 186073 is its powerful electric motor. Boasting a robust design, this trimmer delivers consistent performance without the hassles associated with gas-powered alternatives. The electric motor minimizes noise levels, making it an excellent choice for residential areas where maintaining peace and quiet is essential.

The Weed Eater also emphasizes user comfort with its lightweight construction. At just a few pounds, it enables extended use without causing fatigue, thereby making it suitable for individuals of varying strength. Additionally, the adjustable handle ensures optimal control and maneuverability, allowing users to navigate around flower beds, fences, and other obstacles with precision.

Another technological highlight of the Weed Eater 186073 is its automatic line feed system. This feature saves time by eliminating the need for manual adjustments. When the trimmer encounters tension, it seamlessly releases additional line, allowing users to maintain a continuous cutting edge without interruption. This system also minimizes line wastage, contributing to cost efficiency over time.

The trimmer is equipped with a 12-inch cutting width, which strikes an excellent balance between power and manageability for trimming grass and weeds. This width is perfect for small to medium-sized yards, making quick work of overgrown areas without being cumbersome.

Durability is a key characteristic of the Weed Eater 186073. Made with high-quality materials, it is built to withstand the rigors of outdoor use. Whether it's tackling tough weeds or simply maintaining a pristine lawn, this trimmer has been designed to perform reliably under various conditions.

Furthermore, the Weed Eater 186073 is eco-friendly, producing zero emissions during operation. This commitment to environmental responsibility aligns with the growing trend towards sustainable gardening practices.

In summary, the Weed Eater 186073 is a powerful, lightweight, and efficient electric string trimmer equipped with advanced features that cater to both novices and experienced gardeners. Its user-friendly design, durable construction, and smart technologies make it an indispensable tool for maintaining a beautiful lawn and garden. For those looking to simplify their yard work while achieving professional results, the Weed Eater 186073 stands out as an excellent choice.