To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

	HEADLIGHT
HOOD	WIRE
HOOD	CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned.Tighten clamp screw securely.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

IDLE SPEED SCREW

PLATE

THROTTLE CABLE

CLAMP

SCREW

HOLE “A”

THROTTLE LEVER

FAST

FIG. 29

186073 specifications

The Weed Eater 186073 is a notable addition to the world of outdoor power equipment, designed specifically for homeowners and gardening enthusiasts who value efficiency and ease of use. This electric string trimmer combines innovative features and cutting-edge technology to provide an exceptional lawn care experience.

One of the standout features of the Weed Eater 186073 is its powerful electric motor. Boasting a robust design, this trimmer delivers consistent performance without the hassles associated with gas-powered alternatives. The electric motor minimizes noise levels, making it an excellent choice for residential areas where maintaining peace and quiet is essential.

The Weed Eater also emphasizes user comfort with its lightweight construction. At just a few pounds, it enables extended use without causing fatigue, thereby making it suitable for individuals of varying strength. Additionally, the adjustable handle ensures optimal control and maneuverability, allowing users to navigate around flower beds, fences, and other obstacles with precision.

Another technological highlight of the Weed Eater 186073 is its automatic line feed system. This feature saves time by eliminating the need for manual adjustments. When the trimmer encounters tension, it seamlessly releases additional line, allowing users to maintain a continuous cutting edge without interruption. This system also minimizes line wastage, contributing to cost efficiency over time.

The trimmer is equipped with a 12-inch cutting width, which strikes an excellent balance between power and manageability for trimming grass and weeds. This width is perfect for small to medium-sized yards, making quick work of overgrown areas without being cumbersome.

Durability is a key characteristic of the Weed Eater 186073. Made with high-quality materials, it is built to withstand the rigors of outdoor use. Whether it's tackling tough weeds or simply maintaining a pristine lawn, this trimmer has been designed to perform reliably under various conditions.

Furthermore, the Weed Eater 186073 is eco-friendly, producing zero emissions during operation. This commitment to environmental responsibility aligns with the growing trend towards sustainable gardening practices.

In summary, the Weed Eater 186073 is a powerful, lightweight, and efficient electric string trimmer equipped with advanced features that cater to both novices and experienced gardeners. Its user-friendly design, durable construction, and smart technologies make it an indispensable tool for maintaining a beautiful lawn and garden. For those looking to simplify their yard work while achieving professional results, the Weed Eater 186073 stands out as an excellent choice.

Weed Eater 186073 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: 186073