JVC Theater Surround adjustments
Before you start, remember...
• Make sure that you have set the speaker information correctly |
(see page 14). |
5. | Press TEST again to stop the test tone. | TEST | |
4 | |||
|
| ||
6. | Press EFFECT to select an effect | EFFECT | |
|
|
• There is a time limit in doing the following steps. If the setting is |
level you want.
1
| canceled before you finish, start from step 2 again. |
• | You cannot adjust the rear speaker output levels when you have set |
| “REAR SPK” to “NO.” See page 14. |
• | You cannot adjust the center speaker output level when you have |
| set “CENTER SPK” to “NO.” See page 14. |
From the remote control:
1. Press DSP MODE repeatedly until | DSP |
MODE | |
“THEATER” appears on the |
|
display. |
|
The PRO LOGIC and DSP indicators also light up on the display.
2. Press SOUND. | SOUND |
|
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker | TEST |
output balance. | 4 |
|
“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:
•Each time you press the button, the effect level changes as follows:
DSP EFFECT 1 
DSP EFFECT 2 
DSP EFFECT 3
DSP EFFECT 5 | DSP EFFECT 4 |
As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).
On the front panel:
You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.
1. Press DSP MODE repeatedly until | DSP MODE |
| |
“THEATER” appears on the |
|
display. |
|
The PRO LOGIC and DSP indicators also light up on the display.
| TEST TONE L |
| TEST TONE C |
| TEST TONE R |
| ||||
| (Left front speaker) |
| (Center speaker) |
| (Right front speaker) | |||||
|
| TEST TONE LS |
| TEST TONE RS | ||||||
|
| (Left rear speaker) |
| (Right rear speaker) |
|
| ||||
Notes:
•You can adjust the speaker output levels without outputting the test tone.
•No test tone comes out of the center speaker when “CENTER SPK” is set to “NO” (see page 14).
•No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page 14).
4.Adjust the speaker output levels.
•To adjust the center speaker level, press CENTER +/– (from +10 dB to
•To adjust the left rear speaker level, press REAR•L +/– (from +10 dB to
•To adjust the right rear speaker level, press REAR•R +/– (from +10 dB to
– CENTER+ | – REAR• L+ | – REAR• R+ | |||
2 | 3 | 5 | 6 | 8 | 9 |
| MENU |
| ENTER |
|
|
2.Adjust the speaker output levels.
1)Press ADJUST repeatedly until one of the following indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level. “REAR L LEVEL”:
To adjust the left rear speaker level. “REAR R LEVEL”:
To adjust the right rear speaker level.
2)Press CONTROL UP 5/DOWN °to adjust the selected speaker output level (from +10 dB to
3)Repeat 1) and 2) to adjust the other speaker output levels.
3.Adjust the effect level.
1)Press ADJUST repeatedly until “DSP EFFECT” appears on the display. The display changes to show the current setting.
2)Press CONTROL UP 5/DOWN °to select the effect level.
•Each time you press the button, the effect level changes as follows:
ADJUST SETTING
CONTROL
DOWN UP
ADJUST SETTING
CONTROL
DOWN UP
DSP EFFECT 1 
DSP EFFECT 2 
DSP EFFECT 3 
DSP EFFECT 5 | DSP EFFECT 4 |
As the number increases, JVC Theater Surround becomes stronger (normally set it to “DSP EFFECT 3”).
24
