Weed Eater 259723, 173487 Tractor -- Model Number Decals, Wheels And Tires, Install Seat

Seat Pan
Battery Box	Label
Door

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

• Press lift lever plunger and raise

TRACTOR -- MODEL NUMBER 259723

DECALS

Terminal Terminal

INSTALL SEAT

Adjust seat before tightening adjustment knob.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely.

•Assemble adjustment bolt, lock washer and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

Seat

	attachment lift lever to its highest
	position.
•	Release parking brake by depressing
	clutch/brake pedal.
•	Place gearshift lever in neutral (N)
	position.
•	Roll tractor forward off skid.
• Remove banding holding discharge
	guard up against tractor.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•	Be sure all the above assembly steps
	have been completed.
•	Check engine oil level and fill fuel
	tank with gasoline.
•	Sit on seat in operating position,
	depress clutch/brake pedal and set
	the parking brake.
•	Place gear shift lever in neutral (N)
	position.
•	Press lift lever plunger and raise
	attachment lift lever to its highest
	position.
•	Start the engine. After engine has
	started, move throttle control to idle
	position.

53

9 21

		2
		15
		12
		18
KEY	PART
NO.	NO.	DESCRIPTION
1	156867	Decal Oper P/L Eng
2	64-1726-29 Decal Engine HP
3	164578	Decal Hood Rh
4	164579	Decal Hood Lh
5	162398	Decal Ins Strg Whl
8	164424	Decal Panel Dash
9	171448	Decal Fender Logo
10	145005	Decal Battery Dngr/Psn
11	156439	Decal Danger Fender

4

11

13

8

10

1

KEY	PART
NO.	NO.	DESCRIPTION
12	4900J	Decal Clutch/brake English
15	136832	Decal Mower Drive Schem 38
18	163128	Decal Mower Enviro
21	162392	Decal Grille Logo
- -	138311	Decal Lift Handle
- -	173487	Manual Owners English
- -	173488	Manual Owners Spanish

Shoulder Seat Pan

Bolt

Adjustment	Flat Washer
Bolt	Lock Washer

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

•	Depress clutch/brake pedal into full
	“BRAKE” position and hold. Move
	gearshift lever to 1st gear.
•	Slowly release clutch/brake pedal and
	slowly drive tractor off skid.
•	Apply brake to stop tractor, set parking
	brake and place gearshift lever in
	neutral position.
•	Turn ignition key to “OFF” position.
Continue with the instructions that
follow.

WHEELS AND TIRES

			KEY	PART
			NO.	NO.	DESCRIPTION
			1	59192	Cap Value Tire
			2	65139	Stem Value
1			3	106222X	Tire F Ts 15 X 6 0 - 6 Service
2	5,8		4	59904	Tube Inner Front #35060
			5	106732X427	Rim Asm 6"front White
	4,10
					Service
	7		6	278H	Fitting Grease
	3,9		7	9040H	Bearing Flange
6		11	8	106108X427	Rim Asm 8"rear White Service
			9	124635X	Tire R Ts 18x8 5-8 Service
			10	7152J	Tube Rear 9 5 X 8 Service
			11	104757X	Cap Axle Blk 1 50 X 1 00
			- -	144334	Sealant, Tire (10 oz. tube)

NOTE: All component dimensions given in U. S. inches 1 inch = 25/4 mm

8 41