Dust Cup

2.Remove trimmer head by turning counter- clockwise (looking from bottom of unit).

3.Thread replacement trimmer head onto the shaft by turning clockwise. Only tighten hand tight!

CARBURETOR IDLE SPEED ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool, and secure the unit

before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container.

Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

SReplace your gasoline can if it starts to rust.

11

Page 10 Page 12
Page 11
Image 11
Weed Eater FX26SC, 545186796 Carburetor Idle Speed Adjustment, Seasonal Storage, Fuel System, Engine, Other
Page 10 Page 12

FX26SC, 545186796 specifications

The Weed Eater FX26SC is a versatile and powerful string trimmer designed for homeowners and landscaping professionals who demand performance and reliability. With its 26cc engine, this trimmer delivers ample power to tackle even the toughest grass and weeds, making it an essential tool for maintaining a pristine yard or garden.

One of the standout features of the FX26SC is its ease of use. The trimmer is equipped with a lightweight design, which allows for extended use without causing fatigue. Its balanced weight distribution enhances maneuverability, making it easier to trim around flower beds, fences, and other obstacles in your yard. The ergonomic handle is designed for comfort, providing a secure grip that reduces strain on the hands during operation.

The FX26SC features a dual-line system that enables efficient cutting. This system allows for a wider cutting path, allowing users to finish jobs more quickly while achieving a clean, precise cut. The trimmer also features a bump feed head that automatically advances the line when you tap it on the ground, minimizing downtime and ensuring continuous operation.

In terms of technology, the FX26SC comes with a reliable 2-stroke engine that provides a strong power-to-weight ratio. This engine technology is designed for lower emissions, making it an environmentally friendly choice for users who want to minimize their ecological footprint. The trimmer also features an easy-start system, which reduces the effort needed to start the engine, allowing users to get straight to work without the hassle of cumbersome starting procedures.

Its durable construction ensures that the Weed Eater FX26SC can withstand the rigors of regular use. The frame is designed to resist wear and tear from tough outdoor conditions, prolonging the life of the trimmer. Maintenance is straightforward, with easily accessible parts that make it simple to perform routine checks and repairs.

Overall, the Weed Eater FX26SC is more than just a string trimmer; it's a reliable outdoor tool loaded with features and technologies that enhance performance, comfort, and efficiency. Whether you're a homeowner looking to keep your lawn in check or a professional landscaper needing a dependable tool, the FX26SC meets a variety of cutting needs with ease and precision.
Top Page Image Contents