To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 24)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

TERMINAL	KEPS NUT
COVER

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

Fig. 24

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 25)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

Fig. 25

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

435073, 960180001, 96018000100 specifications

The Weed Eater 96018000100 is a versatile and powerful trimmer designed for homeowners and professionals alike. Known for its efficiency and reliability, this model is a part of Weed Eater's commitment to provide quality outdoor power tools that make yard work easier.

One of the key features of the Weed Eater 96018000100 is its lightweight design, which allows for easy maneuvering and reduces user fatigue during extended use. Weighing in at just over 10 pounds, it offers a balance that is perfect for trimming around flower beds, sidewalks, and hard-to-reach areas. The ergonomic handle design further enhances user comfort, making it suitable for users of varying heights.

Power is critical when it comes to outdoor tools, and the 96018000100 does not disappoint. This model is equipped with a robust 25cc two-cycle engine, providing more than enough power to tackle thick weeds and overgrown foliage. The engine operates efficiently, offering reliable performance while simultaneously ensuring low emissions. This eco-friendly approach aligns with current environmental standards, making it suitable for eco-conscious consumers.

Another standout feature of the Weed Eater 96018000100 is its easy-to-load spool system. The Rapid Reload system allows users to quickly and efficiently load new line without the hassle of disassembling the trimmer head. This innovative design significantly minimizes downtime and enhances productivity, making it a favorite among both seasoned gardeners and weekend warriors.

In terms of cutting capabilities, the 96018000100 boasts a 17-inch cutting width, allowing it to cover more ground with each pass while still delivering precise cuts around edges and hard surfaces. Additionally, the trimmer features an adjustable head, giving users the ability to tilt and reach hard-to-access spots with ease.

Safety is another crucial aspect of the Weed Eater's ethos. The model includes safety features such as a protective guard that minimizes the risk of debris being thrown towards the user while operational. A safety switch also prevents accidental starts, ensuring that this powerful tool is safe for all users.

In conclusion, the Weed Eater 96018000100 merges innovative technology with powerful performance, making it an essential tool for anyone looking to maintain their outdoor space effectively. With its lightweight design, powerful engine, and user-friendly features, it stands out in its category as a reliable and efficient choice for lawn care enthusiasts.

Weed Eater 435073, 96018000100 To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: 435073 960180001 96018000100