CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major en- gine performance and durability problems.

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HELPFUL TIP

If your engine switch reads “push to stop”, it is always in the ON position.

HOW TO STOP YOUR UNIT

STo stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

SIf engine does not stop, move choke to the FULL CHOKE position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

STARTING POSITION

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Primer

Bulb

Choke

Lever

Starter

Handle

Thottle

Trigger

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls. NOTE: If the en- gine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 6 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

7

Page 6 Page 8
Page 7
Image 7
Weed Eater 545186794, FL20C Fuel Requirements, HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Warm Engine
Page 6 Page 8

545186794, FL20C specifications

The Weed Eater 545186794, FL20C is a powerful and versatile string trimmer that is ideal for both homeowners and professional landscapers. With its ergonomic design and advanced technologies, this string trimmer makes yard maintenance easier and more efficient.

One of the standout features of the FL20C is its lightweight construction. Weighing in at only 8.5 pounds, it is easy to maneuver, reducing fatigue during extended use. This makes it an excellent choice for users of all ages and skill levels. The adjustable handle also provides added comfort and control, allowing users to customize the grip to suit their preference.

The FL20C is powered by a robust 20cc two-stroke engine that delivers impressive performance. This engine offers plenty of power for tackling thick grass and weeds, while still being fuel-efficient. The trimmer's speed and performance make it suitable for various outdoor tasks, from trimming around flower beds to edging along driveways and sidewalks.

One of the notable technologies incorporated into the Weed Eater FL20C is its easy-start system. The trimmer's design includes a primer bulb and a choke for quick and effortless starting. This feature is especially beneficial for those who may struggle with traditional string trimmers that require multiple pulls to start.

Additionally, the FL20C uses a bump feed line advance system. This means that when users tap the trimmer head on the ground, it automatically releases more line, ensuring that the user always has an optimal cutting length without having to stop and manually feed the line. This significantly enhances productivity and convenience.

Durability is another key characteristic of the Weed Eater FL20C. Constructed with high-quality materials, it is built to withstand the rigors of regular use. The trimmer head is designed for easy line replacement, minimizing downtime.

For those concerned about safety, the FL20C features a protective guard to shield users from debris while trimming. This added safety measure provides peace of mind during operation.

In summary, the Weed Eater 545186794, FL20C is a standout choice for anyone looking to maintain their yard effectively. With its lightweight design, powerful engine, easy-start technology, bump feed system, and focus on durability and safety, this string trimmer offers exceptional performance for a variety of trimming tasks. Whether for occasional backyard upkeep or regular landscaping work, the FL20C delivers results with ease and efficiency.
Top Page Image Contents