To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

KEPS

NUT

HEX

BOLT

POSITIVE (RED)	NEGATIVE
CABLE	(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

	GOVERNOR	GOVERNOR
	GOVERNOR	CONTROL
	CONTROL LEVER	CONTROL
	CONTROL LEVER	PLATE
		PLATE
HOLES “A”	CLAMP	THROTTLE
	SCREW	CABLE
		CABLE

FIG. 29

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

WE16542D specifications

The Weed Eater WE16542D is a versatile and powerful string trimmer designed to make lawn care and landscaping tasks easier and more efficient. Built with user convenience and performance in mind, this model has gained popularity among both homeowners and landscaping professionals.

One of the standout features of the WE16542D is its lightweight design. Weighing in at just over 10 pounds, it is easily maneuverable, allowing users to trim grass and weeds without feeling fatigued during long periods of use. The trimmer is equipped with a 16-inch cutting swath, providing ample coverage for tackling larger areas quickly while still allowing for precision around flower beds and other landscaping features.

Powering the WE16542D is a reliable 42cc two-cycle gas engine, which delivers robust performance. This engine provides a good balance of power and efficiency, enabling users to handle tougher jobs without a loss of performance. The trimmer also features an easy-start system, ensuring that users can get to work without the frustration of struggling with difficult pull starts.

The Weed Eater WE16542D incorporates a dual-line cutting system with a bump feed head. This technology allows users to effortlessly advance the cutting line while working, which is particularly useful for maintaining a seamless cutting experience. The trimmer's dual-line system ensures a clean and efficient cut, resulting in a more pristine lawn.

Additionally, the trimmer boasts an adjustable ergonomic handle, giving users the ability to customize the grip and orientation to fit their height and comfort level. This thoughtful design feature minimizes user strain, making it ideal for prolonged use. The WE16542D is also equipped with a vibration-reduction system, further enhancing user comfort by reducing the impact of vibrations during operation.

Durability is another hallmark of the Weed Eater WE16542D. The construction is robust, designed to withstand the rigors of outdoor use while maintaining performance over time. With proper care and maintenance, users can expect this trimmer to serve them for many seasons.

In summary, the Weed Eater WE16542D combines lightweight design, powerful performance, and user-friendly features to provide an effective solution for lawn maintenance. Whether you are a homeowner looking to keep your garden pristine or a professional landscaper managing various properties, this trimmer offers reliability and efficiency for all your trimming needs.

Weed Eater WE16542D To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Models: WE16542D