SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER

OF MOWER

TO GROUND

TO GROUND

“A”

“A”

 

GROUND LINE

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

• Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

• If links are not equal in length, adjust one link to same length as other link.

• To lower front of mower loosen nut “E” on both front links an equal number of turns.

20

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDREL

IDLER PULLEYS

PULLEY

 

MANDREL

PULLEY

FIG. 20

Page 19 Page 21
Page 20
Image 20
Weed Eater WE16542D To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation
Page 19 Page 21

WE16542D specifications

The Weed Eater WE16542D is a versatile and powerful string trimmer designed to make lawn care and landscaping tasks easier and more efficient. Built with user convenience and performance in mind, this model has gained popularity among both homeowners and landscaping professionals.

One of the standout features of the WE16542D is its lightweight design. Weighing in at just over 10 pounds, it is easily maneuverable, allowing users to trim grass and weeds without feeling fatigued during long periods of use. The trimmer is equipped with a 16-inch cutting swath, providing ample coverage for tackling larger areas quickly while still allowing for precision around flower beds and other landscaping features.

Powering the WE16542D is a reliable 42cc two-cycle gas engine, which delivers robust performance. This engine provides a good balance of power and efficiency, enabling users to handle tougher jobs without a loss of performance. The trimmer also features an easy-start system, ensuring that users can get to work without the frustration of struggling with difficult pull starts.

The Weed Eater WE16542D incorporates a dual-line cutting system with a bump feed head. This technology allows users to effortlessly advance the cutting line while working, which is particularly useful for maintaining a seamless cutting experience. The trimmer's dual-line system ensures a clean and efficient cut, resulting in a more pristine lawn.

Additionally, the trimmer boasts an adjustable ergonomic handle, giving users the ability to customize the grip and orientation to fit their height and comfort level. This thoughtful design feature minimizes user strain, making it ideal for prolonged use. The WE16542D is also equipped with a vibration-reduction system, further enhancing user comfort by reducing the impact of vibrations during operation.

Durability is another hallmark of the Weed Eater WE16542D. The construction is robust, designed to withstand the rigors of outdoor use while maintaining performance over time. With proper care and maintenance, users can expect this trimmer to serve them for many seasons.

In summary, the Weed Eater WE16542D combines lightweight design, powerful performance, and user-friendly features to provide an effective solution for lawn maintenance. Whether you are a homeowner looking to keep your garden pristine or a professional landscaper managing various properties, this trimmer offers reliability and efficiency for all your trimming needs.
Top Page Image Contents