Installation, Before You Begin | Bosch Appliances D9112 specs

Installation

Before You Begin

This Installation section contains a general installation procedure. It refers you to other sections of the manual for detailed instructions.

Radionics recommends you review this manual and the D9112 Program Entry Guide (74-06145-000) before you begin the installation to determine the hardware and wiring requirements for the features you want to use.

Have the following additional documents handy as you read through this manual:

•D9112 Program Record Training Sheet (74-06447-000)

•Security System Owner’s Manual (71-06633-000)

•D1255 Command Center Installation Manual (74-06819-000)

Before you begin the installation of the D9112 you should be familiar with the operation of the D5200 programmer or the RAM II remote programmer.

Enclosure Options

Mount the D9112 Control/Communicator assembly in any of the Radionics enclosures listed below. Refer to the Installation Guide for UL and Fire Applications in this manual to determine if your application requires a specific enclosure.

•D8103 Universal Enclosure (gray)

•D8109 Fire Enclosure (red)

•D8108A Attack Resistant Enclosure (gray)

Beginning the Installation

Mounting the Enclosure

Mount the enclosure in the desired location. Be certain to use all five mounting holes. See Figure 2.

POINT CHART LABEL MOUNTING SKIRT HOOK

MODULE MOUNTING

LOCATIONSTAMPER SWITCH

MOUNTING LOCATION

MOUNTING

SKIRT HOOK

MODULE

MOUNTING

LOCATIONS

HOOK OPENINGS

BACK OF D9112

LOCK-DOWN TAB

SKIRT MOUNTING HOLE

Figure 2: Enclosure Mounting

	D9112	Operation & Installation Manual
			© 1993 Radionics
74-06144-000-C 2/96		Page 13

Image 13

Bosch Appliances D9112 Before You Begin, Enclosure Options, Beginning the Installation, Mounting the Enclosure

Contents

D I O N I C S Part FCC Notices 74-06144-000-C 2/96 Table of Contents Installation Guide for UL and Fire Applications Programmer and Accessory ConnectionsCurrent Rating Chart for Standby Battery Calculation for Figures and Tables D8128A OctoPOPIT Switch Settings Points Introduction Keyswitch D1255 Alpha III Command CenterAreas and Accounts Communicator Event Log Event MemoryEMI/Lightning Transient Protection Programming Other Features D9112 Assembly D9112 Control/Communicator AssemblyOrdered Separately Literature Pack Fire Listings and ApprovalsBurglary Factory Mutual FM Beginning the Installation InstallationBefore You Begin Enclosure Options Premises Wiring Connecting Earth Ground TerminalInstalling the D9112 Assembly Lock the Reset Pin Now Locking the Reset Pin Charge the Battery as You Finish Finishing the InstallationInstall and Wire Detection Devices Install Modules and Relays Connect the On-Board Points and Command Centers Install the Point Chart LabelPower Up Programming the Panel Testing the System Primary Power Terminals Power SupplyPrimary AC Power Circuit Installing the Transformer Secondary DC Power Secondary Power TerminalsInstalling the Battery Battery Supervision Battery Discharge/Recharge Schedule No AC Power Battery Charging CircuitFloat Charge Discharge Cycle Low Battery LED Red Charging Status and Low Battery LEDsCharging Status LED Yellow Available Power Power OutputsCircuit Protection Accessory Connector J2 Continuous Power Outputs TerminalsContinuous Current Draw Expansion Port J4 Relay Installation Programmable Power Outputs TerminalsProgramming Optional Relays Required Verification/Reset Relay Available PowerTerminals 6 Terminal Registration Telephone ConnectionsNotification Location Phone LED Red Phone Cord ConnectionOperation Monitor LED Green Dialing Format Ground Start Relay Installation Ground Start Jumper D128 Dual Phone Line SwitcherDescription Operation Installing the D128 Watchdog FeaturePrimary Phone Lines, Primary Phone Numbers D128 Status LEDs AC Power LEDPrimary Fail LED Secondary Fail LED Description Terminals 11 to On-Board PointsPoint Sensor Loops Point Response Time Point Parameters Point Zonex Buss Terminals 23 to Off-Board PointsD8125 Popex Module D8127 Popit Modules Wiring the D8125 to the D9112 Installing the D8125 Popex ModuleListings Mounting D8125 D9112Zonex +UP to 63 Point Points Data Expansion Loop Wire Specifications Wiring POPITs to the Data Expansion Loop Popit Sensor Loops Wiring Data Expansion Loops to Popex Modules D9112 Program Record Sheet Point Assignments Popit Labels Vertical Grid for Popex #1 D8128A OctoPOPIT Module Installing the OctoPOPITListing D8128A OctoPOPITs Wiring OctoPOPITs to the D9112 Line Termination Point Assignment Switches Sensor Loop SwitchesOctoPOPIT Sensor Loops Sensor Loop D9112 Point # Testing Off-board Points Off-board Relays Configuring the D8129 OctoRelayD8129 OctoRelay Relay Outputs D8129 Switch Settings Wiring Connections Installation Relay Output D811 Arm Status Relay Module D811 Module Wiring D1255 Address Settings D1255 Command Centers Terminals 29 toArming Devices Description D1255 Connections D9112 Command Center Terminal Function Wire Color D9112 Power at Command Centers Maintained Contact Keyswitch OperationMomentary Contact Silencing the Bell Programmer Connector J7 Programmer and Accessory Connections Programmer Access Reports Accessory Connector J2Expansion Port J4 D9112 Terminal Name Description Quick Reference Terminal Description Installation Guide for UL and Fire Applications Optional Compatible Equipment IntroductionBurglary Applications Fire Applications Fire Applications Enclosures D129 Class a System Chart System Wiring Diagram, Issue a Total a = Total B = Total C 1 = Current Rating Chart for Standby Battery CalculationsCurrents shown in milliamperes 1 ampere=1000 milliamperes Central Station or Local Fire Alarm Standby Battery RequirementsRemote Station or Auxiliary Fire Alarm Household Burglary and Commercial Burglary Central Station or Local Systems Current Chart First Household Fire Ampere-Hour Calculation Formula Remote Station or Auxiliary Systems Self Diagnostics Troubleshooting GuideCall for Service Trouble at Command Center Panel Broken Hardware, Software Failed Servc Batt LOW Battery Voltage Low Servc AC Fail AC Power FailedServc Batt Msing Battery Missing, Shorted, or Reversed Servc Keypad Supervised Command Center Missing Phone Line Trouble Symptom Diagnosis Remedy Communications Failure Zonex BUS Problems Programming the Panel See Problems with Data Expansion Loop Problems with Points Symptom Diagnosis Remedy Symptom Diagnosis Remedy Metering the Loops Problems with the D8125 Popex Data Expansion Loops Checking Shielded Cable EMI on Long Wire Runs NCI #1, #40 Problems with Command Centers Watchdog Reset Reports Battery and Power ReportsRunaway Reports to the Receiver Overloaded Power Supply Service Walk Test Service Walk ? Command 5 9 Shows Firmware Revision Command 5 7 Toggles Default Idle TextPress Command 5 Specifications SDI Bus Compatible AccessoriesTelephone Connections Environmental