D9112 Control/Communicator Assembly

The Radionics D9112 Control/Communicator is shipped pre-assembled from the factory. You should receive the following parts with your D9112 panel.

Literature Pack

•D9112 Installation Reference Guide (74-06144-000)

•D9112 Program Record Sheet (74-06100-000)

•UL Smoke Detector Compatibility Technogram (73-06143-000)

•Point Chart Label (79-06660-000)

•Eight 1k ý end-of-line resistors

•Two 14", 18 AWG, color-coded battery leads

D9112 Assembly:

•D9112 PC board

•Faceplate shield

•Mounting Skirt

•One #6x1¦4" screw

Ordered Separately

Order the following to complete a basic 8 point D9112 installation.

•D1255 Command Center (or keyswitch)

•D1640 Transformer

•D126 Battery

•D161 or D162 Phone Cord

(order two cords if you are using the D128 Dual Phone Switcher)

• D8103, D8109, or D8108A Enclosure

	D9112 Operation & Installation Manual
	D9112 Operation & Installation Manual	© 1993 Radionics
74-06144-000-C 2/96	Page 11	© 1993 Radionics

Page 11

Image 11

Bosch Appliances D9112 Control/Communicator Assembly, Ordered Separately, Literature Pack, D9112 Assembly

Contents

D I O N I C S Part FCC Notices 74-06144-000-C 2/96 Table of Contents Standby Battery Calculation for Programmer and Accessory ConnectionsInstallation Guide for UL and Fire Applications Current Rating Chart for Figures and Tables D8128A OctoPOPIT Switch Settings Points Introduction Communicator D1255 Alpha III Command CenterKeyswitch Areas and Accounts Programming Event MemoryEvent Log EMI/Lightning Transient Protection Other Features Literature Pack D9112 Control/Communicator AssemblyD9112 Assembly Ordered Separately Factory Mutual FM Listings and ApprovalsFire Burglary Enclosure Options InstallationBeginning the Installation Before You Begin Installing the D9112 Assembly Connecting Earth Ground TerminalPremises Wiring Lock the Reset Pin Now Locking the Reset Pin Install Modules and Relays Finishing the InstallationCharge the Battery as You Finish Install and Wire Detection Devices Programming the Panel Install the Point Chart LabelConnect the On-Board Points and Command Centers Power Up Testing the System Installing the Transformer Power SupplyPrimary Power Terminals Primary AC Power Circuit Battery Supervision Secondary Power TerminalsSecondary DC Power Installing the Battery Discharge Cycle Battery Charging CircuitBattery Discharge/Recharge Schedule No AC Power Float Charge Charging Status LED Yellow Charging Status and Low Battery LEDsLow Battery LED Red Circuit Protection Power OutputsAvailable Power Expansion Port J4 Continuous Power Outputs TerminalsAccessory Connector J2 Continuous Current Draw Optional Relays Required Programmable Power Outputs TerminalsRelay Installation Programming Terminal Available PowerVerification/Reset Relay Terminals 6 Location Telephone ConnectionsRegistration Notification Dialing Format Phone Cord ConnectionPhone LED Red Operation Monitor LED Green Ground Start Relay Installation Operation D128 Dual Phone Line SwitcherGround Start Jumper Description Primary Phone Lines, Primary Phone Numbers Watchdog FeatureInstalling the D128 Secondary Fail LED AC Power LEDD128 Status LEDs Primary Fail LED Point Sensor Loops On-Board PointsDescription Terminals 11 to Point Response Time Point Parameters D8125 Popex Module D8127 Popit Modules Off-Board PointsPoint Zonex Buss Terminals 23 to Mounting Installing the D8125 Popex ModuleWiring the D8125 to the D9112 Listings +UP to 63 Point Points D9112D8125 Zonex Data Expansion Loop Wire Specifications Wiring POPITs to the Data Expansion Loop Popit Sensor Loops Wiring Data Expansion Loops to Popex Modules D9112 Program Record Sheet Point Assignments Popit Labels Vertical Grid for Popex #1 Listing Installing the OctoPOPITD8128A OctoPOPIT Module D8128A OctoPOPITs Wiring OctoPOPITs to the D9112 Line Termination OctoPOPIT Sensor Loops Sensor Loop SwitchesPoint Assignment Switches Sensor Loop D9112 Point # Testing Off-board Points Relay Outputs Configuring the D8129 OctoRelayOff-board Relays D8129 OctoRelay D8129 Switch Settings Wiring Connections Installation Relay Output D811 Arm Status Relay Module D811 Module Wiring Description D1255 Command Centers Terminals 29 toD1255 Address Settings Arming Devices D1255 Connections D9112 Command Center Terminal Function Wire Color D9112 Power at Command Centers Silencing the Bell Keyswitch OperationMaintained Contact Momentary Contact Programmer Connector J7 Programmer and Accessory Connections Expansion Port J4 Accessory Connector J2Programmer Access Reports D9112 Terminal Name Description Quick Reference Terminal Description Installation Guide for UL and Fire Applications Fire Applications IntroductionOptional Compatible Equipment Burglary Applications Fire Applications Enclosures D129 Class a System Chart System Wiring Diagram, Issue a Currents shown in milliamperes 1 ampere=1000 milliamperes Current Rating Chart for Standby Battery CalculationsTotal a = Total B = Total C 1 = Household Burglary and Commercial Burglary Standby Battery RequirementsCentral Station or Local Fire Alarm Remote Station or Auxiliary Fire Alarm Central Station or Local Systems Current Chart First Household Fire Ampere-Hour Calculation Formula Remote Station or Auxiliary Systems Panel Broken Hardware, Software Failed Troubleshooting GuideSelf Diagnostics Call for Service Trouble at Command Center Servc Keypad Supervised Command Center Missing Servc AC Fail AC Power FailedServc Batt LOW Battery Voltage Low Servc Batt Msing Battery Missing, Shorted, or Reversed Phone Line Trouble Symptom Diagnosis Remedy Communications Failure Zonex BUS Problems Programming the Panel See Problems with Data Expansion Loop Problems with Points Symptom Diagnosis Remedy Symptom Diagnosis Remedy Metering the Loops Problems with the D8125 Popex Data Expansion Loops Checking Shielded Cable EMI on Long Wire Runs NCI #1, #40 Problems with Command Centers Runaway Reports to the Receiver Battery and Power ReportsWatchdog Reset Reports Overloaded Power Supply Service Walk Test Service Walk ? Press Command 5 Command 5 7 Toggles Default Idle TextCommand 5 9 Shows Firmware Revision Specifications Environmental Compatible AccessoriesSDI Bus Telephone Connections