Continuous Power Outputs Terminals | Bosch Appliances D9112 guide

Available Power (Continued)

Accessory Connector (J2)

The D128 Dual Phone Line Switcher connects to J2.

Expansion Port (J4)

The Expansion Port is reserved for future use.

Continuous Power Outputs

Terminals

3

24

J2

Continuous Current Draw

32

J4

The continuous current draw for powered devices connected to terminals 3, 8, 24, and 32, the Expansion Port (J4), and the Accessory Connector (J2) must not exceed 1.4A . Devices powered from these outputs must operate over a range of 10.2 VDC to 13.9 VDC.

Power restricted for fire and combined fire/burglary systems: Use the Fire System Power Formula to calculate the current available for fire and combined fire/burglary systems. See Programmable Power Outputs.

	D9112 Operation & Installation Manual
74-06144-000-C 2/96	Page 24	© 1993-1996 Radionics

Image 24

Bosch Appliances D9112 Continuous Power Outputs Terminals, Continuous Current Draw, Accessory Connector J2

Contents

D I O N I C S FCC Notices Part 74-06144-000-C 2/96 Table of Contents Programmer and Accessory Connections Installation Guide for UL and Fire ApplicationsCurrent Rating Chart for Standby Battery Calculation for D8128A OctoPOPIT Switch Settings Figures and Tables Introduction Points D1255 Alpha III Command Center KeyswitchAreas and Accounts Communicator Event Memory Event LogEMI/Lightning Transient Protection Programming Other Features D9112 Control/Communicator Assembly D9112 AssemblyOrdered Separately Literature Pack Listings and Approvals FireBurglary Factory Mutual FM Installation Beginning the InstallationBefore You Begin Enclosure Options Connecting Earth Ground Terminal Premises WiringInstalling the D9112 Assembly Locking the Reset Pin Lock the Reset Pin Now Finishing the Installation Charge the Battery as You FinishInstall and Wire Detection Devices Install Modules and Relays Install the Point Chart Label Connect the On-Board Points and Command CentersPower Up Programming the Panel Testing the System Power Supply Primary Power TerminalsPrimary AC Power Circuit Installing the Transformer Secondary Power Terminals Secondary DC PowerInstalling the Battery Battery Supervision Battery Charging Circuit Battery Discharge/Recharge Schedule No AC PowerFloat Charge Discharge Cycle Charging Status and Low Battery LEDs Low Battery LED RedCharging Status LED Yellow Power Outputs Available PowerCircuit Protection Continuous Power Outputs Terminals Accessory Connector J2Continuous Current Draw Expansion Port J4 Programmable Power Outputs Terminals Relay InstallationProgramming Optional Relays Required Available Power Verification/Reset RelayTerminals 6 Terminal Telephone Connections RegistrationNotification Location Phone Cord Connection Phone LED RedOperation Monitor LED Green Dialing Format Relay Installation Ground Start D128 Dual Phone Line Switcher Ground Start JumperDescription Operation Watchdog Feature Installing the D128Primary Phone Lines, Primary Phone Numbers AC Power LED D128 Status LEDsPrimary Fail LED Secondary Fail LED On-Board Points Description Terminals 11 toPoint Sensor Loops Point Parameters Point Response Time Off-Board Points Point Zonex Buss Terminals 23 toD8125 Popex Module D8127 Popit Modules Installing the D8125 Popex Module Wiring the D8125 to the D9112Listings Mounting D9112 D8125Zonex +UP to 63 Point Points Wiring POPITs to the Data Expansion Loop Data Expansion Loop Wire Specifications Wiring Data Expansion Loops to Popex Modules Popit Sensor Loops Point Assignments D9112 Program Record Sheet Vertical Grid for Popex #1 Popit Labels Installing the OctoPOPIT D8128A OctoPOPIT ModuleListing Wiring OctoPOPITs to the D9112 D8128A OctoPOPITs Line Termination Sensor Loop Switches Point Assignment SwitchesOctoPOPIT Sensor Loops D9112 Point # Sensor Loop Testing Off-board Points Configuring the D8129 OctoRelay Off-board RelaysD8129 OctoRelay Relay Outputs D8129 Switch Settings Installation Wiring Connections D811 Arm Status Relay Module Relay Output D811 Module Wiring D1255 Command Centers Terminals 29 to D1255 Address SettingsArming Devices Description D9112 Command Center Terminal Function Wire Color D1255 Connections Power at Command Centers D9112 Keyswitch Operation Maintained ContactMomentary Contact Silencing the Bell Programmer and Accessory Connections Programmer Connector J7 Accessory Connector J2 Programmer Access ReportsExpansion Port J4 D9112 Quick Reference Terminal Description Terminal Name Description Installation Guide for UL and Fire Applications Introduction Optional Compatible EquipmentBurglary Applications Fire Applications Fire Applications Enclosures System Chart D129 Class a System Wiring Diagram, Issue a Current Rating Chart for Standby Battery Calculations Total a = Total B = Total C 1 =Currents shown in milliamperes 1 ampere=1000 milliamperes Standby Battery Requirements Central Station or Local Fire AlarmRemote Station or Auxiliary Fire Alarm Household Burglary and Commercial Burglary Current Chart First Central Station or Local Systems Remote Station or Auxiliary Systems Household Fire Ampere-Hour Calculation Formula Troubleshooting Guide Self DiagnosticsCall for Service Trouble at Command Center Panel Broken Hardware, Software Failed Servc AC Fail AC Power Failed Servc Batt LOW Battery Voltage LowServc Batt Msing Battery Missing, Shorted, or Reversed Servc Keypad Supervised Command Center Missing Symptom Diagnosis Remedy Phone Line Trouble Communications Failure Problems Programming the Panel Zonex BUS Problems with Points See Problems with Data Expansion Loop Symptom Diagnosis Remedy Symptom Diagnosis Remedy Problems with the D8125 Popex Data Expansion Loops Metering the Loops EMI on Long Wire Runs Checking Shielded Cable Problems with Command Centers NCI #1, #40 Battery and Power Reports Watchdog Reset ReportsRunaway Reports to the Receiver Overloaded Power Supply Service Walk Test Service Walk ? Command 5 7 Toggles Default Idle Text Command 5 9 Shows Firmware RevisionPress Command 5 Specifications Compatible Accessories SDI BusTelephone Connections Environmental