Bosch Appliances D9112 Power Outputs

D9112 Operation & Installation Manual

Page 23

© 1993 Radionics

74-06144-000-C 2/96

Power Outputs

Circuit Protection

Three self-resetting thermal circuit breakers protect the panel from short circuits on both

the continuous and programmable power outputs. The circuit breakers are thermal rated

and open at 3 to 5 Amps. If the panel is programmed for power supervision and short is

sustained on one of the power outputs, the panel transmits a BATTERY LOW or

BATTERY MISSING for Modem II, or TROUBLE ZN 9 for BFSK.

One thermal circuit breaker protects Terminal 3 - Auxiliary Power and Terminal 24 -

ZONEX Power and the Expansion Port (J4). A short on one disrupts the power to the

others.

One breaker protects Terminal 6 - Alarm Power Output, Terminal 7 - Alternate Alarm

Power Output, and Terminal 8 - Switched Auxiliary Power. A short on one of these

terminals disrupts the power to the other two.

One circuit breaker protects terminal 32 - Power +.

Warning, Minimum Requirement for Wire Length:

Connect powered devices to

terminals 3, 6, 7, 8, 24, and 32 with at least 5 feet of 22 AWG wire or 14 feet of 18 AWG

wire. A D9112, with devices connected with shorter lengths of wire, may not operate

properly if AC power is interrupted.

Available Power

The D9112 produces up to 1.4A of power at 10.2 VDC to 13.9 VDC for powered devices.

The outputs listed below share the available power.

Terminal 3 - Auxiliary Power

Use this terminal to power devices requiring continuous power.

Terminal 6 (Relay A) - Alarm Power Output

Terminal 7 (Relay B) - Alternate Alarm Power Output

Use terminals 6 and 7 to power devices requiring power on alarm. See

Programmable

Power Outputs.

Terminal 8 (Relay C) - Switched Auxiliary Power

Use this terminal to power devices requiring a programmable power interruption.

Command 47 or Alarm Verification interrupts the power . See

Programmable Power

Outputs

in this manual.

Terminal 24 - ZONEX Power

Use this terminal to power ZONEX modules such as the D8125, D8128A, and D8129

modules.

Terminal 32 - Power +

Use this terminal to power SDI (Serial Device Interface) devices such as the D1255

Command Center and the D9131 Parallel Printer Interface.

Contents

Main Notice FCC Notices Part 15 Part 68 Part 68 Table of Contents Page Figures and Tables Introduction Points Areas and Accounts Communicator D1255 Alpha III Command Center Keyswitch Event Memory Event Log EMI/Lightning Transient Protection Programming NCI 154 Other Features D9112 Control/Communicator Assembly Ordered Separately Listings and Approvals Fire Burglary Installation Before You Begin Installation Guide for UL and Fire Applications D1255 Command Center Installation Manual Security System Owners Manual Connecting Earth Ground Terminal 10 Locking the Reset Pin Existing reports transmitted with Reset Pin locked down: RAM Parameters Answer Armed Locking Reset Speeds Programming: Finishing the Installation Charge the Battery as You Finish Install and Wire Detection Devices Install Modules and Relays Make the Telephone Connections Programming the Panel Install the Point Chart Label Testing the System Power Supply Primary Power Terminals 1 2 Primary (AC) Power Circuit Installing the Transformer Secondary Power Terminals 45 Secondary (DC) Power Installing the Battery Battery Supervision Battery Supervision (Continued) Investigate low battery reports right away Reset or power down required for shorted battery: Load Shed Relay protects battery: Battery Charging Circuit Charging Status and Low Battery LEDs Charging Status LED (Yellow) No missing battery with D192A Reset required for shorted battery: Power Outputs Power Outputs Circuit Protection Warning, Minimum Requirement for Wire Length: Available Power Programmable Power Outputs. Available Power (Continued) Continuous Power Outputs Terminals 3 24 32 J2 J4 Continuous Current Draw Programmable Power Outputs Terminals 6 7 8 Programming Bell Parameters Unexpected Output at Terminals 6, 7 and 8: Bell Parameters Fire System Power Formula Terminal 8 Telephone Connections % RJ31X MODULE PREMISES Registration Notification Phone Cord Connection Phone LED (Red) #221 Bad line may test OK: Phone Parameters Phone Line Test Points Communication Failure Dont rely on relay labeling: Ground Start Relay Installation D128 Dual Phone Line Switcher Operation D9112 Program Entry Guide Primary Phone Lines, Primary Phone Numbers Dont confuse primary phone lines with primary phone numbers: Communication Failure D9112 Program Entry Guide Panel Wide Parameters D128 Status LEDs On-Board Points Description Terminals 11 to 22 Ground shunts cause missed alarms: D9112 Program Entry Guide (74-06145-000) Point Sensor Loops Point Parameters Point Response Time Warning, increasing debounce count may cause missed alarms: Debounce Count Point Assignment Off-Board Points Point (ZONEX) Buss Terminals 23 to 28 D8125 POPEX Module D8127 POPIT Modules Listings Installation Guide for UL and Fire Installing the D8125 POPEX Module Wiring the D8125 to the D9112 Wiring the D8125 to the D9112 D8125 Figure 12: D8125 Connections D9112 Wiring POPITs to the D8125 for instructions on connecting POPITs to the D8125 POPEX module. Maximum Length of All Data Expansion Loops Combined AWG Length (Feet) 22 1,800 20 2,890 18 4,600 16 7,320 14 11,650 Wiring Data Expansion Loops to POPEX Modules POPIT Sensor Loops Premises Wiring Installation Point Assignments 1993 Radionics 74-06144-000-C 2/96 POPIT SWITCH SETTING Figure 15: POPIT Labels D9112 POINT NUMBER Vertical Grid for POPEX #1 PLACE SMALL LABEL ON THIS TERMINAL BLOCK D8112 STYLE ZONEX FORMAT POPEX MODULE NUMBER D8112 MASTER ZONE 1 D8112 MASTER ZONE 2 D8128A OctoPOPIT Module Warning, Do not use D8128 modules, they are not compatible with the D9112, only use D8128A modules: Line Termination, Sensor Loop Switches, Tampered enclosures for UL certificated systems: Troubleshooting Wiring OctoPOPITs to the D9112 Power down first: OctoPOPIT Sensor Loops OctoPOPIT Point Assignments. Line Termination OctoPOPIT Sensor Loops Point Assignment Switches #215 Duplicated points do not function correctly: Always set the Sensor Loop switch for points 72 and 136 to OFF: #215 D8128A Switche s 91011 D8128A Sensor Loop Testing Off-board Points Off-board Relays D8129 OctoRelay Warning: D8129 restricted for fire systems: Page Do not use the instructions packaged with the D8129: Configuring the D8129 OctoRelay Power Outputs Wiring Connections D811 Arm Status Relay Module Relay numbers for D811 not programmable: Do not use the instructions packaged with the D811: Warning: D811 restricted for fire systems: Wiring Connections Figure 18: D811 Module Wiring Arming Devices Description D9112 Program Entry Guide Command Center Assignment Security System Owners Manual D9112 Command Center Terminal Function Wire Color Function D9112 and D8132 (or other power supply) must share COMMON: Power Outputs Extra power needed for more command centers: Switching the green and yellow wires affects other command centers: D268/D269 Independent Zone Control D279 Independent Zone Control OctoPOPIT D279 Operation and Installation Instructions D9112 Program Entry Guide Point Assignments Keyswitch Relays FA Bypass Max Area Wide Parameters FA Bypass Max Programmer and Accessory Connections Programmer Connector (J7) Troubles after 30 seconds: Locking Reset Speeds Programming: D5200 Programmer Operation Manual Accessory Connector (J2) Expansion Port (J4) Plugging a programmer into J4 causes PT BUSS TROUBLE report: It may also cause erroneous alarm and/or trouble reports from Off-board points. 1993-1996 Radionics74-06144-000-C 2/96 D9112 Faceplate M J2 J2 + Quick Reference Terminal Description Terminal Name Description Installation Guide for UL and Fire Applications Listings and Approvals Fire Burglary Introduction D9112 System Chart Test weekly: Off-Board Relays Smoke Detectors Compatible with the D9112 Fire Applications (Continued) Enclosures D9112 System Chart System Chart Electrically Actuated * Remote Station or # System Wiring Diagram, Issue A D9131 PARALLEL PARALLEL OR D811 ARM STATUS RELAY D1640 Current Rating Chart for Standby Battery Calculations Total A = ____ Total B = ____ Total C Standby Battery Requirements Household Burglary and Commercial Burglary Central Station or Local Fire Alarm Remote Station or Auxiliary Fire Alarm Household Fire Warning Equipment Standby Battery Calculation for NFPA 72 Fire Alarm Applications Current Chart First D9112 Standby Battery and Current Rating Chart Central Station or Local Systems Remote Station or Auxiliary Systems Household Fire Warning Equipment Troubleshooting Guide Introduction Silencing the buzzer does not correct the problem: Telephone Connections Operation Monitor LED Battery and Power Reports Communication Failure Telephone Connections Phone Line Trouble Communications Failure Relays Communications Failure Phone D9112 Program Entry Guide Problems Programming the Panel Problems with Points Problems with Data Expansion Loop Problems with Points NCI #215 Page Problems with the D8125 POPEX Data Expansion Loops EMI EMI on Long Wire Runs Metering the Loops Checking Shielded Cable EMI on Long Wire Runs Problems with Command Centers User Interface Area Parameters Passcode Worksheet Passcode Work sheet Battery and Power Reports D9112 Program Entry Guide Touch Terminal 10 first: Overloaded Power Supply Power Outputs Overloaded Power Supply Service Walk Test Page Command 5 7 Toggles Default Idle Text AREA # IS ON AREA # IS OFF 9112 REV # # - # # Command 5 9 Shows Firmware Revision Battery Discharge/Recharge Schedule Specifications Relays Voltage Input Current Requirements D9112 Standby Battery and Current Rating Chart SDI Bus Telephone Connections Environmental Arming Stations Point Thresholds