To Level Mower Housing, Belt Removal | Weed Eater WET1338B manual

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inﬂated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinﬂated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF	BOTTOM EDGE
MOWER	OF MOWER
TO GROUND	TO GROUND

“A”	“A”
	GROUND LINE

FIG. 16

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 17

FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

FIG. 18

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 19

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 20)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Disconnect R.H.suspension arm from rear deck bracket by removing retainer spring.

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work new belt around both mandrel pulleys and idler pulleys.

•Install new belt into engine pulley grove.

•Reconnect R.H. suspension arm and secure with re- tainer spring.

•Make sure belt is in all pulley grooves and inside all belt guides.

WET1338B specifications

The Weed Eater WET1338B is a powerful and efficient string trimmer designed for homeowners and professional landscapers alike. This robust tool is engineered to tackle a variety of cutting tasks, making it a versatile addition to any lawn care arsenal.

One of the standout features of the WET1338B is its 38cc two-cycle engine, which delivers impressive performance and reliability. This engine offers users the power needed to cut through thick grass, weeds, and even light brush without sacrificing efficiency. Its lightweight design ensures that users can maneuver it easily around their yards, reducing fatigue during extended use.

In terms of technology, the Weed Eater WET1338B is equipped with a 17-inch cutting width, allowing for a wide swath of grass to be trimmed with each pass. This feature significantly cuts down on the time needed to complete landscaping tasks. The dual-line trimmer head provides a professional finish while allowing for easy line replacement. The automatic line advancement system ensures that the cutting line is managed effectively, so users can focus on the job without worrying about running out of line mid-task.

Comfort and usability are at the forefront of the WET1338B’s design. The trimmer includes an adjustable handle that provides optimal control and comfort. The cushioned grip reduces vibrations during use, enhancing the overall user experience. The lightweight build of the trimmer also minimizes strain, making it suitable for users of varying physical abilities.

Moreover, the WET1338B is crafted with durability in mind. Its rugged construction is designed to withstand the rigors of regular use, ensuring that it remains a reliable tool for years to come. The fuel-efficient engine allows users to work longer without frequent refueling, adding to its practicality.

Safety features are also an essential aspect of the Weed Eater WET1338B. The inclusion of a protective guard enhances user safety, preventing debris from being thrown towards the operator during use.

Overall, the Weed Eater WET1338B stands out as a feature-rich, user-friendly string trimmer that effectively meets the demands of lawn care professionals and enthusiastic homeowners. Its combination of power, durability, and ease of use makes it a valuable investment for anyone looking to maintain their outdoor space with minimal effort.

Weed Eater WET1338B manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Models: WET1338B