To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

FIG. 27

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned.Tighten clamp screw securely.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

IDLE SPEED SCREW

PLATE

THROTTLE CABLE

CLAMP

SCREW

HOLE “A”

THROTTLE LEVER

FAST

FIG. 28

WET1338B specifications

The Weed Eater WET1338B is a powerful and efficient string trimmer designed for homeowners and professional landscapers alike. This robust tool is engineered to tackle a variety of cutting tasks, making it a versatile addition to any lawn care arsenal.

One of the standout features of the WET1338B is its 38cc two-cycle engine, which delivers impressive performance and reliability. This engine offers users the power needed to cut through thick grass, weeds, and even light brush without sacrificing efficiency. Its lightweight design ensures that users can maneuver it easily around their yards, reducing fatigue during extended use.

In terms of technology, the Weed Eater WET1338B is equipped with a 17-inch cutting width, allowing for a wide swath of grass to be trimmed with each pass. This feature significantly cuts down on the time needed to complete landscaping tasks. The dual-line trimmer head provides a professional finish while allowing for easy line replacement. The automatic line advancement system ensures that the cutting line is managed effectively, so users can focus on the job without worrying about running out of line mid-task.

Comfort and usability are at the forefront of the WET1338B’s design. The trimmer includes an adjustable handle that provides optimal control and comfort. The cushioned grip reduces vibrations during use, enhancing the overall user experience. The lightweight build of the trimmer also minimizes strain, making it suitable for users of varying physical abilities.

Moreover, the WET1338B is crafted with durability in mind. Its rugged construction is designed to withstand the rigors of regular use, ensuring that it remains a reliable tool for years to come. The fuel-efficient engine allows users to work longer without frequent refueling, adding to its practicality.

Safety features are also an essential aspect of the Weed Eater WET1338B. The inclusion of a protective guard enhances user safety, preventing debris from being thrown towards the operator during use.

Overall, the Weed Eater WET1338B stands out as a feature-rich, user-friendly string trimmer that effectively meets the demands of lawn care professionals and enthusiastic homeowners. Its combination of power, durability, and ease of use makes it a valuable investment for anyone looking to maintain their outdoor space with minimal effort.

Weed Eater WET1338B manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: WET1338B