SERVICE AND ADJUSTMENTS

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

 

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

 

 

 

 

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

 

HEADLIGHT

HOOD

WIRE

CONNECTOR

 

22

FIG. 26

Page 22
Image 22
Weed Eater WET2242STD manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

WET2242STD specifications

The Weed Eater WET2242STD is a powerful and versatile string trimmer designed to meet the needs of both homeowners and landscape professionals. This reliable tool offers a perfect blend of performance, ease of use, and innovative features that make it an excellent choice for tackling even the toughest yard maintenance tasks.

One of the standout features of the WET2242STD is its robust 22cc, 2-cycle engine. This powerful engine provides ample power to cut through dense vegetation, making it an ideal choice for trimming grass, weeds, and overgrown areas. The engine's lightweight design contributes to reduced fatigue during extended use, allowing operators to work comfortably for longer periods.

The trimmer features an adjustable curved shaft, which ensures versatility in handling different tasks while providing optimal balance and reduced vibration. This design allows users to easily maneuver around flower beds, rocks, and other obstacles, making trimming more efficient and enjoyable. The WET2242STD also incorporates a dual-line feed system, which automatically advances the cutting line as needed, ensuring consistent cutting performance without interruptions.

Durability is a key characteristic of the WET2242STD. Its high-quality construction is built to withstand the rigors of regular use, featuring components that are resistant to wear and tear. The trimmer is also equipped with a protective shield that enhances safety while providing protection against debris.

In terms of technology, the WET2242STD utilizes an easy-start system that simplifies the process of getting the unit running, reducing the time and effort required to start the engine. This feature is especially beneficial for those who may be new to using string trimmers, as it minimizes frustration and ensures a quick start-up with minimal fuss.

Another noteworthy aspect of the WET2242STD is its user-friendly design. The trimmer is equipped with an ergonomic handle that provides a comfortable grip and reduces strain on the hands during operation. This thoughtful design feature enhances user control and precision when navigating around tight spaces.

Overall, the Weed Eater WET2242STD is a reliable, high-performance string trimmer that combines an efficient engine with user-friendly features. Its lightweight design, adjustable shaft, and automatic line feed system make it an excellent addition to any lawn care toolkit. Whether you're a homeowner looking to maintain your yard or a professional landscaper, the WET2242STD delivers impressive results with every use.