OPERATION
TURNING
•Release the drive control bar.
•Move throttle control to “SLOW” position.
•Place shift lever indicator in “F” (forward) position. Tines will not turn.
•Lift handle to raise tines out of ground.
•Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines.
•When you have completed your
OUTER SIDE SHIELDS (See Fig. 11)
The back edges of the outer side shields are slotted so that the shields can be raised for deep tilling and lowered for shallow tilling to protect small plants from being buried. Loosen nut “A” in slot and nut “B”. Move shield to desired position (both sides). Retighten nuts.
TO TRANSPORT
CAUTION: Before lifting or transporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.
AROUND THE YARD
•Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in posi- tion. This prevents tines from scuffing the ground.
•Place shift lever indicator in “F” (forward) position for transporting.
•Hold the drive control bar against the handle to start tiller movement. Tines will not turn.
•Move throttle control to desired speed.
AROUND TOWN
•Disconnect spark plug wire.
•Drain fuel tank.
•Transport in upright position to prevent oil leakage.
BEFORE STARTING ENGINE
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS.
CHECK ENGINE OIL LEVEL (See Fig. 12)
•The engine in your unit has been shipped, from the factory, already filled with SAE 30 summer weight oil.
•Be sure tiller is level and the area around oil fill is clean.
•Check oil level before each use. Add oil if needed. Fill to full line on dipstick.
•To read proper level, tighten engine oil cap each time.
•Reinstall engine oil cap and tighten.
•For approximate capacity see “PRODUCT SPECIFIC- ATIONS” on page 3 of this manual. All oil must meet A.P.I. Service Classification
•For cold weather operation you should change oil for easier starting (See oil viscosity chart in the Mainte- nance section of this manual).
•To change engine oil, see the Maintenance section in this manual.
OIL FILL
CAP/DIPSTICK
FIG. 12
ADD GASOLINE
•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.
CAUTION: Fill to within 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is ac- cidentally spilled, move machine away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.
Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.
CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
9
