2. Attach the Bench Frame (1) to the Front Leg (2) | 2 |
|
|
|
|
|
with two M10 x 65mm Bolts (40), two M10 |
|
|
|
|
| |
|
|
|
|
|
| |
Washers (44), and two M10 Nylon Locknuts (43). |
|
| 40 |
|
| |
Do not tighten the Locknuts. |
|
|
|
| ||
|
|
|
|
|
| |
|
|
|
|
|
| 1 |
|
| 44 |
|
|
|
|
|
|
|
| 40 |
| |
| 43 |
|
|
|
|
|
|
|
| 2 |
|
|
|
3. Attach the Bench Frame (1) to the Crossbar (4) | 3 |
|
|
|
|
|
with two M10 x 81mm Bolts (41) and two M10 |
|
|
|
|
| |
|
|
|
|
|
| |
Nylon Locknuts (43). |
|
|
| 4 |
|
|
Tighten the M10 Nylon Locknuts (43) used in |
|
|
|
|
| 43 |
steps 1 through 3. |
|
| 41 |
|
|
|
|
|
|
|
|
| |
|
|
| 1 | 41 |
|
|
|
|
|
|
|
| |
4. Attach the Weight Tube (16) inside the Leg Lever | 4 |
|
|
|
|
|
(3) with an M8 x 58mm Bolt (52), two M8 |
|
|
|
|
| |
|
|
|
|
|
| |
Washers (56), a 10mm Spacer (32), and an M8 |
|
|
| 43 | 2 |
|
Nylon Locknut (55). |
|
|
|
|
| |
|
| 3 |
|
|
| |
|
|
|
|
|
| |
Press the 25mm Round Angled Cap (28) onto the |
|
|
|
|
| Grease |
Weight Tube (16). |
|
|
|
|
| |
| 55 |
|
|
|
| |
|
| 32 |
| 28 | 54 | |
Grease an M10 x 68mm Bolt (54). Attach the Leg |
|
|
| |||
|
|
|
| |||
| 56 |
|
|
|
| |
Lever (3) with the Bolt and an M10 Nylon Locknut |
|
|
|
|
| |
(43). Do not overtighten the Locknut; the Leg |
|
|
|
|
|
|
Lever must be able to pivot easily. |
| 16 | 56 | 52 |
|
|
|
|
|
|
| ||
|
|
|
|
|
| |
5. Orient the Backrest Frames (12) with the indicat- | 5 | 49 |
|
|
| |
ed holes closer to the bottom. Attach the Backrest |
| Holes |
| |||
| 48 |
| ||||
Frames to the Backrest Bracket (10) with four M6 |
|
|
|
| ||
|
|
|
|
|
| |
x 40mm Bolts (49), four M6 Washers (48), and |
|
| 48 |
|
|
|
four M6 Nylon Locknuts (51). Do not tighten the |
|
|
|
| 48 | |
Locknuts. |
|
|
|
|
| |
|
|
|
|
|
| |
|
|
| 12 | 51 | 48 | 49 |
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
| 10 |
| 51 |
|
|
|
|
|
|
| |
6
