![](/images/new-backgrounds/1293246/29324621x1.webp)
19. Wrap the Long Cable (80) under a 90mm Pulley | 19 |
|
|
|
|
(28) as shown. Attach the Pulley and a Cable |
|
|
|
| |
|
|
|
|
| |
Trap (29) to the Upright (3) with an M10 x 120mm |
|
|
|
|
|
Button Head Bolt (40) and an M10 Nylon Locknut |
| 3 |
|
|
|
(76). Make sure the Cable Trap is oriented to |
|
|
|
| |
|
|
|
|
| |
hold the Cable in the groove of the Pulley. |
|
|
| 28 | 76 |
| 40 |
|
| ||
|
|
|
|
| |
|
|
|
|
| 80 |
|
|
|
| 29 |
|
20. Attach a Pulley Housing (94) to the indicated “U”- | 20 |
|
|
|
|
channel on the |
|
|
|
| |
|
|
|
|
| |
(44) with an M10 x 102mm Button Head Bolt (24), |
|
|
|
|
|
two Pivot Bushings (74), and an M10 Nylon |
| 44 |
|
|
|
Locknut (76). |
| 74 |
| 74 |
|
|
|
|
| ||
Wrap the Long Cable (80) around a 90mm Pulley |
| 94 |
|
| 76 |
(28). Attach the Pulley inside of the Pulley | 24 |
| 76 |
| |
Housing (94) with an M10 x 42mm Button Head |
|
|
| ||
|
|
|
| ||
Bolt (71) and an M10 Nylon Locknut (76). |
| 71 |
|
|
|
|
|
|
| 28 |
|
|
|
|
| 80 |
|
21. Wrap the Long Cable (80) around a 90mm Pulley | 21 |
|
|
|
|
(28). Attach the Pulley and a Cable Trap (29) to |
|
|
|
| |
|
|
|
|
| |
the indicated M10 x 140mm Carriage Bolt (73) |
|
| 28 |
|
|
with an M10 Nylon Locknut (76). Make sure the |
|
|
|
| |
Cable Trap is oriented to hold the Cable in the |
|
|
|
|
|
groove of the Pulley. |
| 80 |
| 76 |
|
|
|
|
| ||
|
|
|
|
| |
|
|
| 29 |
|
|
22. Make sure there are no Resistance Bar (not |
|
|
|
|
|
shown) under the |
|
|
| 73 |
|
Center Resistance Bar (not shown). Have a sec- |
|
|
|
| |
ond person pull on the Long Cable (80) to create |
|
|
|
|
|
slack in the Cable. | 22 |
|
|
|
|
Insert the end of the Long Cable (80) through the |
|
|
|
|
|
welded tube on the indicated end of the Cross |
|
|
| 71 |
|
Tube (11) and then through the remaining Swivel |
|
|
|
| |
|
| 22 | 8 |
| |
Arm (22). Be sure the Cable is on the indicated |
| Rod |
| ||
side of the welded rod in the Swivel Arm. |
|
|
|
| |
80 |
|
|
|
| |
|
|
|
|
| |
Insert the Swivel Arm (22) into the welded tube |
|
|
| 11 |
|
on the Cross Tube (11). Secure the Swivel Arm |
| 28 | 76 |
| |
|
|
| |||
with an M4 x 5mm Screw (8). |
|
|
|
| |
|
|
|
|
| |
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
|
(28). Attach the Pulley inside of the Swivel Arm |
|
|
|
|
|
(22) with an M10 x 42mm Button Head Bolt (71) |
|
|
|
|
|
and an M10 Nylon Locknut (76). |
|
|
|
|
|
| 11 |
|
|
|
|