![](/images/new-backgrounds/1298421/29842115x1.webp)
4. Insert the connector of the lower wire harness (A) | 4 |
| 6 | 78 | |
into the socket of the Upper Wire Harness (13). | 13 | ||||
|
|
| |||
The connector should slide easily into the sock- |
|
|
| ||
|
|
|
| ||
et and snap into place. If the connector does not |
| 3 |
|
| |
slide easily and snap into place, turn the connector |
| A |
| ||
over and then insert it. |
|
|
|
| |
Make sure that the connector and wire appear as |
| 79 | 13 |
| |
|
|
| |||
shown in the inset drawing. IF THE CONNEC- |
|
|
|
| |
TOR IS NOT INSERTED PROPERLY, THE CON- |
|
|
|
| |
SOLE MAY BE DAMAGED WHEN THE POWER |
|
|
|
| |
IS TURNED ON. |
|
| 71 |
| |
|
|
|
| ||
Pull the excess lower wire harness (A) out of |
|
|
|
| |
the Mech Assembly (6) and push it and the |
|
|
|
| |
Upper Wire Harness (13) into the Upright (3). |
|
|
| A | |
|
|
|
| ||
Insert the Mech Assembly (6) into the Base (1). |
|
| 13 |
| |
|
|
|
| ||
Attach the Mech Assembly to the Upright (3) with |
|
| 1 |
| |
a 1/2” x 66mm Carriage Bolt (79) and a 1/2” |
|
|
| ||
|
|
|
| ||
Nylon Jamnut (78). Do not tighten the Jamnut |
|
| 71 |
| |
yet. |
|
|
| ||
|
|
|
| ||
Attach the Mech Assembly (6) to the Base (1) | 5 |
|
|
| |
|
|
|
| ||
with four M10 Nylon Locknuts (71). |
|
| 71 |
| |
|
|
|
| ||
Tighten the 1/2” Nylon Jamnut (78). |
|
|
|
| |
5. Press the Front Leg Foot (29) onto the bottom of |
|
|
| 23 | |
|
|
|
| ||
the Front Leg (31). Note that the front of the |
|
|
| 71 | |
Front Leg Foot is taller than the back. |
|
|
| ||
| 91 | 31 |
| ||
|
|
| |||
|
|
|
| ||
Attach the Bench Rail (23), with the hook on the |
| 104 | 30 |
| |
bottom, to the Front Leg (31) with two M10 x |
|
| |||
|
|
| |||
53mm Carriage Bolts (91) and two M10 Nylon |
| Front |
|
| |
Locknuts (71). |
| 29 |
| ||
|
|
|
| ||
Attach the Leg Lever Bumper (30) to the front |
|
|
|
| |
Leg (31) with an M4 x 19mm Screw (104). |
|
|
|
| |
6. Grease an M10 x 103mm Bolt (86) using the | 6 |
|
|
| |
|
|
| 3 | ||
included grease pack. Attach the Bench Rail (23) |
|
|
| ||
|
|
|
| ||
to the Upright (3) with the Bolt and an M10 Nylon |
|
|
|
| |
Locknut (71). Make sure the Bolt is inserted |
|
|
|
| |
through the indicated hole in the Bench Rail. |
|
|
|
| |
Do not overtighten the Locknut; the Bench |
|
| 26 |
| |
Rail must be able to pivot easily. |
|
| 71 |
| |
|
|
|
| ||
Tighten the Storage Knob (26) into the Upright (3) |
|
| Hole |
| |
and the Bench Rail (23). |
|
|
| ||
| 23 | 86 | |||
|
|
|
| Grease | |
| 8 |
|
|
|