4. Insert the connector of the lower wire harness (A) | 4 |
| 6 | 78 | |
| into the socket of the Upper Wire Harness (13). | 13 | |||
|
|
|
| ||
| The connector should slide easily into the sock- |
|
|
| |
|
|
|
|
| |
| et and snap into place. If the connector does not |
| 3 |
|
|
| slide easily and snap into place, turn the connector |
| A |
| |
| over and then insert it. |
|
|
|
|
| Make sure that the connector and wire appear as |
| 79 | 13 |
|
|
|
|
| ||
| shown in the inset drawing. IF THE CONNEC- |
|
|
|
|
| TOR IS NOT INSERTED PROPERLY, THE CON- |
|
|
|
|
| SOLE MAY BE DAMAGED WHEN THE POWER |
|
|
|
|
| IS TURNED ON. |
|
| 71 |
|
|
|
|
|
| |
| Pull the excess lower wire harness (A) out of |
|
|
|
|
| the Mech Assembly (6) and push it and the |
|
|
|
|
| Upper Wire Harness (13) into the Upright (3). |
|
|
| A |
|
|
|
|
| |
| Insert the Mech Assembly (6) into the Base (1). |
|
| 13 |
|
|
|
|
|
| |
| Attach the Mech Assembly to the Upright (3) with |
|
| 1 |
|
| a 1/2” x 66mm Carriage Bolt (79) and a 1/2” |
|
|
| |
|
|
|
|
| |
| Nylon Jamnut (78). Do not tighten the Locknut |
|
| 71 |
|
| yet. |
|
|
| |
|
|
|
|
| |
| Attach the Mech Assembly (6) to the Base (1) | 5 |
|
|
|
|
|
|
|
| |
| with four M10 Nylon Locknuts (71). |
|
| 71 |
|
| Tighten the 1/2” Nylon Jamnut (78). |
|
|
|
|
5. Press the Front Leg Foot (29) onto the bottom of |
|
|
| 23 | |
|
|
|
| ||
| the Front Leg (31). Note that the front of the |
|
| 71 |
|
| Front Leg Foot is taller than the back. |
|
|
| |
|
| 91 | 31 |
| |
|
|
|
| ||
|
|
|
|
| |
| Attach the Bench Rail (23), with the hook on the |
|
|
|
|
| bottom, to the Front Leg (31) with two M10 x |
|
|
|
|
| 53mm Carriage Bolts (91) and two M10 Nylon |
| Front |
|
|
| Locknuts (71). |
| 29 |
| |
|
|
|
|
| |
6. | Grease an M10 x 103mm Bolt (86) using the | 6 |
|
| 3 |
| included grease pack. Attach the Bench Rail (23) |
|
| ||
|
|
|
| ||
|
|
|
|
| |
| to the Upright (3) with the Bolt and an M10 Nylon |
|
|
|
|
| Locknut (71). Make sure the Bolt is inserted |
|
|
|
|
| through the indicated hole in the Bench Rail. |
|
|
|
|
| Do not overtighten the Locknut; the Bench |
|
|
|
|
| Rail must be able to pivot easily. |
|
| 26 |
|
| Tighten the Storage Knob (26) into the Upright (3) |
|
| 71 |
|
|
|
|
|
| |
| and the Bench Rail (23). |
|
| Hole |
|
|
|
|
|
| |
|
|
| 23 | 86 |
|
|
|
|
| Grease | |
|
| 8 |
|
|
|
