ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with
Assembly requires the included hex keys and your own phillips screwdriver | , wire cutters | |
and needlenose pliers | . |
|
For help identifying the assembly hardware, see the PART IDENTIFICATION CHART in the centre of this manual. Note: The assembly hardware and other small parts are packaged in separate part bags. Do not open the part bags until instructed to do so.
1. Make sure that the power cord is unplugged. | 1 |
| 60 |
|
|
|
|
|
| ||
Place the Base (79) in the position shown, with the indi- | 61 | 63 |
|
| |
| 73 |
|
| ||
cated small holes on top (only one small hole is shown). | Bolt | 64 |
|
| |
Place a Wheel (63) in each Wheel Housing (62), and | Hole |
|
|
| |
|
|
|
| ||
slide the Wheel Housings onto the ends of the Base that |
|
| 62 |
|
|
have bolt holes. |
|
|
|
| |
|
|
| 60 |
| |
|
|
| 64 |
| |
Open part bag A. Attach the Wheels (63) to the Wheel |
|
|
| 63 | |
|
|
|
| ||
Housings (62) with 2 1/2” Bolts (61) and Wheel Nuts |
| 79 |
|
|
|
(64). Make sure that the Wheel Nuts are on the sides |
|
| 73 |
|
|
shown; do not overtighten the Bolts. |
|
|
|
| |
|
|
|
|
| |
Slide the two Base Endcaps (75) onto the other ends of | 60 |
|
| 62 | 61 |
73 |
|
|
|
| |
the Base (79) (only one Base Endcap is shown). Attach |
|
|
|
| |
the four Base Pads (73) to the Base Endcaps and the | 75 |
| Small Hole |
|
|
Wheel Housings (62) with four 1 1/4” Tek Screws (60). |
|
|
| ||
|
|
|
|
| |
2. Raise the Base (79) to a vertical position, and hold it | 2 |
|
|
|
|
near the treadmill Frame (96) as shown. Make sure that | 63 |
|
|
| |
|
|
|
| ||
the Wheels (63) are in the indicated position. |
|
| 58 |
|
|
Identify the Right Upright (104), which has a large round |
| 57 |
|
| |
47 |
|
|
|
| |
hole in the indicated location. Feed the Wire Harness |
| 79 |
|
| |
|
|
|
| ||
(65) into the hole and out of the top of the Right Upright. |
|
|
| 63 | |
Make sure that there are two |
|
|
|
|
|
end of the Right Upright (see drawing 2a). Hold the Right |
|
|
|
|
|
Upright against the Base (79) as shown. Make sure that |
|
|
|
| 58 |
the Right Upright is oriented so the pivot hole is in the |
|
|
|
|
|
position shown. Hand tighten two 3” Bolts (58) with two |
|
| 104 |
|
|
5/16” Star Washers (57) into the bottom of the Base and |
|
|
|
| |
|
|
|
|
| |
the lower end of the Right Upright. |
| Pivot |
|
| 57 |
|
|
|
| ||
|
| Holes |
|
| |
Attach the Left Upright (47) to the Base (79) in the same |
|
|
|
| |
|
|
| Round | ||
way. Note: There is not a wire harness on the left side. |
|
|
| ||
|
|
|
| Hole | |
| 2a |
|
|
| |
With the help of a second person, raise the Uprights (47, |
|
|
| 65 | |
104 |
| 96 |
| ||
104) to a vertical position. |
|
|
| ||
|
|
|
| ||
| 74 |
|
|
|
|
6
