2.Identify the Right Upright (37), which has a large round hole near the lower end, and the Left Upright (32).
See drawing 2a. Make sure that there are two
See drawing 2b. Have a second person hold the Base
(55)so it is resting on the Wheels (34) as shown. Attach the Right and Left Uprights (32, 37) to the Base with four Upright Bolts (28) and four 5/16” Star Washers (68). Do not tighten the Bolts yet. Make sure that the large hole in the Right Upright is on the side shown, and that the two small holes in the Left Upright are on the side shown. In addition, make sure that the Base is oriented so the Base Pads (31) are in the location shown.
3.With the help of a second person, place the Frame (21) between the Uprights (32, 37). Feed the Wire Harness (53) into the large round hole near the lower end of the Right Upright (37), and then pull the Wire Harness out of the upper end as shown.
See drawing 3a. Raise the Uprights (32, 37) to the vertical position. Hold an Upright Spacer (58) against one side of the Frame (21) as shown. Insert a Frame Bolt (36) into the indicated hole in the Upright Spacer and the Frame. Next, tighten a Spacer Screw (86) into the Upright Spacer and the Frame. Remove the Frame Bolt. Repeat on the other side of the Frame.
With the help of a second person, carefully lift the Frame (21), and hold the Upright Spacers (58) between the Right Upright (37) and the Left Upright (not shown). Align the in- dicated hole in the Right Upright with the hole in the right Upright Spacer. Next, insert a Frame Bolt (36), with a 3/8” Star Washer (104), into the Right Upright and the Upright Spacer, and loosely thread the Upright Bolt into the Frame.
Repeat this step on the left side of the treadmill.
4.Identify the Right Handrail (5), which has a large hole in the left side. Feed the Wire Harness (53) into the hole in the bottom of the Right Handrail and out of the large hole in the side. Note: It may be helpful to use needlenose pli- ers to pull the Wire Harness out of the hole.
Set the Right Handrail (5) onto the right Upright (37). Attach the Right Handrail with a Upright Bolt (28) as shown. Firmly tighten the Upright Bolt.
Attach the Left Handrail (4) as described above. Note: There is not a wire harness on the left side.
2 | 2a |
|
|
Hole |
|
|
|
37 | 93 |
| 32, 37 |
2b |
|
|
|
Small |
|
|
|
Holes |
|
| 68 |
| 55 | 32 |
|
37 |
|
| |
31 |
| 28 | |
|
|
| |
| 68 |
| 31 |
|
|
| |
|
|
| 34 |
Large | 28 |
|
|
Hole |
|
|
|
3 |
|
|
|
32 |
|
|
|
|
|
| Hole |
|
| 21 | 53 |
|
|
| |
| 37 |
| |
| 53 |
| |
3a |
|
| 37 |
|
|
| |
|
|
| 104 |
58 | 86 |
| 36 |
|
| ||
|
|
| |
21 |
| Holes |
|
|
|
| |
4 |
|
|
|
28 |
|
|
|
| 4 | 53 |
|
|
|
| Hole |
| 28 |
| |
| 32 |
|
|
| 5 |
| Hole |
|
|
| |
|
|
| 37 |
7
