3.Remove the two remaining Latch Screws (14) from the left Upright (38).
Without removing the tape from the Latch Bracket (16) and the Latch Spacer (13), attach both parts to the left Upright (38) with the four Latch Screws (14).
Make sure that the Latch Screws are tight, but do not overtighten them; if the Latch Screws are overtightened, the Storage Latch (17) will not slide smoothly. Remove any visible tape from the Latch Bracket and the Latch Spacer.
Note: The inset drawing shows how the Latch Bracket (16), Latch Springs (15), Storage Latch (17), and Latch Spacer (13) fit together.
4.Remove the shipping tie from the Left Handrail (4) and Handrail Spacer (3). Attach the Left Handrail and Handrail Spacer to the left Upright (38) with two Handrail Bolts (1) and Handrail Washers (70) as shown. Make sure that the ramp on the Handrail Spacer is on the inside as shown. Do not tighten the Handrail Bolts until step 5 is completed.
Remove the shipping tie from the Right Handrail (32) and Handrail Spacer (3). Hold the Handrail Spacer against the right Upright (38) and feed the excess Wire Harness (53) into the right Upright. Attach the Right Handrail and Handrail Spacer to the right Upright with two Handrail Bolts (1) and Handrail Washers (70). Do not tighten the Handrail Bolts until step 5 is completed.
5.Note that the wire ties in the Right Handrail (32) should not be removed. Attach the Console Base (87) to the Handrails (4, 32) with four Console Screws (5). Insert the excess Wire Harness (53) into the right Upright (32). Make sure that the Console
Screws are tight, but do not overtighten them.
Tighten the four Handrail Bolts (1) used in step 4.
6.Remove the backing from the Adhesive Clip (80). Press the Adhesive Clip onto the right Upright (38) in the indicated location. Press the Allen Wrench (81) into the Adhesive Clip.
7.The Console (11) requires three "AA" batteries (not included); alkaline batteries are recommended.
Open the Battery Cover (12) as shown. Press three batteries into the battery compartment, with the neg- ative (Ð) ends of the batteries touching the springs.
Close the battery cover, push up on the battery cover tab, and then push the tab forward as shown in the inset drawing. Be sure that the tab locks into place.
8.Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or carpet from damage, place a mat under the treadmill.
6
3 |
|
|
|
17 |
| 38 |
|
14 | 13 | 13 |
|
|
|
| |
| 16 |
|
|
|
|
| 15 |
|
| 16 | 17 |
|
|
| |
4 |
|
|
|
4 | 38 | 32 | 38 |
|
| ||
|
| Ramps | |
70 |
|
| |
3 |
| 3 | |
| 53 | ||
|
| ||
1 |
|
|
|
|
| 70 |
|
|
| 1 |
|
5 |
|
| 53 |
|
|
| |
4 |
| Wire ties |
|
|
| 87 |
|
| 5 | 32 | 5 |
|
| ||
6 |
|
|
|
|
| 38 |
|
|
| 81 |
|
|
| 80 |
|
7 | 12 |
|
|
11 |
|
| |
|
|
| |
Batteries |
| Battery Cover Tab | |
|
|
| |
