10 I Carefully tilt washer backwards until front of washer is

3-4 inches (7.5-l 0 centimeters) off of floor. Insert piece of wood as brace.

11 Use legs and nuts from parts n package. Screw nut down to

within l/2 inch (1.3 centimeters) of base.

Insert legs into correct holes at each front corner of washer until nuts touch washer. Do Not tiahten nuts until Step1 5.

13 Tilt washer backward and n remove wood block. Gently

lower washer to floor.

Move washer to its final location. Remove cardboard or hardboard from under washer.

I I

14 Tilt washer forward, raising n back legs 1 inch (2.5

centimeters) off of floor to adjust rear self- leveling legs. Gently lower washer to floor. Check levelness of the washer by placing a carpenter’s level on top of the washer, first side to side; then front to back.

I

the front legs up or down to adjust. Repeat Step 14.

When washer is level, use wrench to turn nuts on front legs up tightly against washer base. If nuts are not tight against washer base, the washer may vibrate.

Property Damage

Secure the drain hose to the tub or standpipe with the shipping strap removed from the back of the washer.

Failure to properly secure drain hose could result in water damage.

Measure and mark a point approximately 15 inches (38.1 centimeters) from the plug end of the shipping strap. Cut the shipping strap at this point.

Check that hose is not twisted or kinked and is securely in place.

Put ‘hook” end of drain hose in tub or standpipe. Tightly wrap the shipping strap around the drain hose and tub or standpipe or inlet hose as shown in Figures A-C. Push plug into the nearest hole in the shipping strap.

‘I!i’-1 ’ ‘IJd

If a longer drain hose is needed, drain hose (Part No. 388423) and hose extension kit (Part No. 285442) are available from authorized parts distributors. If drain hose must be shortened, use hose kit (Part No. 285442).

Note: If washer is moved to adjust drain hose, the washer must be leveled again. Repeat Steps 14- 15. Place cardboard under the washer and carefully move washer to avoid damaging floor covering.

17 CHECK ELECTRICAL

n REQUIREMENTS.BESUREYOU HAVE CORRECTELECTRICALSUPPLYAND RECOMMENDED EARTHING METHOD.

18 n Check that all parts are now installed. See parts list, Panel A. If there is an extra part, go back through steps to see which step was skipped.

19 Turn on water faucets and n check for leaks. Tighten

couplings if there is leaking. DO NOT OVERTIGHTEN;this could cause damage to faucet.

20 Check that you have all of n your tools. Check that the

shipping strap with 2 cotter pins and plug was removed from the back of the washer and used to secure the drain hose.

21 Untape power supply cord W and plug into earthed outlet.

22 Take a few minutes and n read the Use and Care

Guide to fully understand your new washer. Now start the washer and allow it to complete the regular cycle.

successfully installed your new Whirlpool washer. To get the most efficient use

from your new washer, read your Whirlpool Use and Care Guide.

Congratulations!

Keep Installation Instructions and Guide. The instructions will make reinstalling your Whirlpool washer in another home

Panel C

Page 3 Page 5
Page 4
Image 4
Whirlpool 220/240-volt installation instructions ‘I!i’-1 ’ ‘IJd, Congratulations
Page 3 Page 5

220/240-volt specifications

Whirlpool is a renowned brand in the home appliance industry, offering a diverse range of products designed to enhance convenience and efficiency in everyday life. Among their extensive lineup, Whirlpool 220/240-volt appliances stand out, catering to regions with higher voltage requirements. These high-voltage appliances are engineered to deliver optimal performance, ensuring that users can carry out household tasks with ease.

One of the main features of Whirlpool 220/240-volt appliances is their robust power capacity. Operating at this voltage allows for faster heating and more efficient operation, which is particularly noticeable in cooking and laundry appliances. This efficiency not only saves time but also helps reduce energy consumption, making them an environmentally friendly choice for the modern household.

Whirlpool leverages advanced technologies in their 220/240-volt appliances to enhance usability and functionality. For instance, many models come equipped with smart sensors that adjust temperature and humidity levels automatically, allowing for precise cooking and drying. This intelligent design ensures that users get perfect results every time, whether they are baking, frying, or washing clothes.

Another significant characteristic of Whirlpool 220/240-volt appliances is their innovative design. They are crafted with user-friendly interfaces, complete with digital displays and intuitive controls that simplify operation. Whether it’s choosing a washing cycle, setting the oven timer, or adjusting the temperature of a refrigerator, users can navigate their appliances effortlessly.

Durability is also a hallmark of Whirlpool products. The materials used in these appliances are selected for their resilience, ensuring they can withstand the rigors of daily use. Additionally, many models feature self-cleaning options or easily accessible maintenance points, extending their lifespan and saving users time on upkeep.

Whirlpool prioritizes energy efficiency across its range of 220/240-volt appliances. Models are designed to minimize energy usage without compromising performance, which is an important factor for eco-conscious consumers. Many units carry Energy Star certification, indicating they meet stringent energy efficiency guidelines.

In summary, Whirlpool's 220/240-volt appliances are designed for power, efficiency, and durability. With advanced technologies, user-friendly features, and a commitment to energy conservation, they provide an exceptional experience for households. Whether cooking, cleaning, or cooling, these appliances are built to meet the demands of modern living while ensuring user satisfaction.
Top Page Image Contents