Before you start...

 

 

 

 

 

 

 

Your safety and the safety of

DANGER

 

 

others is very important.

 

We have provided many important

You will be killed or seriously injured if

 

safety messages in this manual and on

you don’t follow instructions.

your appliance. Always read and obey all

 

 

 

WARNING

 

 

safety messages.

 

 

 

 

 

 

This is the safety alert

 

 

 

 

 

 

 

 

 

 

You can be killed or seriously injured if

 

 

symbol. This symbol alerts

 

 

you to hazards that can kill or

you don’t follow instructions.

 

 

hurt you and others. All safety

All safety messages will identify the hazard,

messages will be preceded by the safety

tell you how to reduce the chance of injury,

alert symbol and the word “DANGER” or

and tell you what can happen if the

“WARNING”. These words mean:

instructions are not followed.

 

 

 

 

 

 

Coin-operated washers are equipped with a meter case, console, timer, selector switches and indicator lights. The coin slide mechanism, slide mounting bolt, slide extension, service door panel lock and key, top lock and key, coin vault, and coin vault lock and key are not included with this washer and are needed to complete installation. These items are available from usual industry sources.

Check location where washer will be installed. Proper installation is your responsibility. Make sure you have everything necessary for correct installation.

Do Not store or operate washer below 32°F some water may remain in washer).

See Use & Care Guide for “Winterizing” information.

Single washer

Grounded

installations require

electrical outlet

12” minimum risers

is required. See

to provide an air

Electrical

cushion and

requirements.

prevent noise and

 

damage to valves.

 

Hot and cold water faucets must be within 4 feet of the back of the washer and provide water pressure 10-100 PSI. A pressure reduction valve should be used in the supply line where inlet pressure entering the building exceeds 100 PSI to prevent damage to the washer mixing valve.

Untape and open washer lid. Remove packages and hoses from washer.

No. T20 Torx

 

 

screws

 

Level floor: Maximum slope

 

 

under washer — 1 inch

 

 

 

 

Water heater: Set to deliver 140°F to 160°F water to the washer.

Standpipe drain system: Needs a two- inch minimum carry-away capacity of 17 gallons per minute. Top of standpipe must be at least 34 inches high and no higher than 72 inches from bottom of washer.

On coin-operated washers, front access to the pump area is available by removing the two, No. 10 Torx screws and then removing the front panel. Non-coin-operated washers do not have a removable front panel. The cabinet and top assembly must be removed by removing clips under console on the non-coin-operated washer.

PAGE 2

A floor drain should be provided under the bulkhead. Prefabricated bulkheads with electrical outlets, water supply lines and drain facilities should be used only where local codes permit.

Non-coin-operated washers are equipped with a console, push to start timer, selector switches and indicator lights (not pictured).

Support: Floor must be sturdy enough to support loaded washer weight of 315 pounds.

Important: Observe all governing codes and ordinances.

Page 1 Page 3
Page 2
Image 2
Whirlpool 3360620 installation instructions Before you start, Your safety and the safety Others is very important
Page 1 Page 3

3360620 specifications

The Whirlpool 3360620 is an essential component for those looking to enhance the functionality of their kitchen appliances, specifically designed for certain models of Whirlpool refrigerators. This replacement part primarily serves as a door shelf bin, catering to the storage needs of users by providing additional space and organization for condiments, beverages, and small food items.

One of the standout features of the Whirlpool 3360620 is its robust construction. Made from high-quality plastic, it is designed to withstand the rigors of daily use while maintaining its structural integrity over time. This durability ensures that it won’t easily warp or crack, providing long-lasting service in the often humid environment of a refrigerator.

The design of the 3360620 is also noteworthy. It features a clear, see-through appearance, allowing users to quickly identify contents without needing to remove the bin. This transparency enhances organization and efficiency, making it easier to find what you need at a glance. Measuring approximately 13 x 6 inches, it fits perfectly within the door of compatible Whirlpool models, maximizing space and usability.

Another significant characteristic of this replacement part is its ease of installation. Designed as a direct fit for specific Whirlpool refrigerator models, it can be installed without the need for special tools, making it accessible for most users to replace on their own. This feature is particularly important for those who prefer DIY repairs and maintenance.

In terms of compatibility, the Whirlpool 3360620 fits several refrigerator models, and it’s always recommended to check the appliance’s model number to ensure a proper fit. This versatility makes it a popular choice among Whirlpool users who seek to prolong the lifespan of their appliances while maintaining organized storage solutions.

Overall, the Whirlpool 3360620 door shelf bin combines durability, efficient design, and easy installation, making it a valuable addition to any Whirlpool refrigerator. It helps users keep their kitchen organized and maximizes the available space, reflecting Whirlpool’s commitment to quality and customer satisfaction.
Top Page Image Contents