Typical full load sizes.
Load Type Loading Suggestion Load Type Loading Suggestion
Mixed 3 double sheets Heavy 3 pair pants
Load 4 pillowcases work 3 shirts
8 T-shirts clothes 1 coverall
6 pair shorts 4 pair jeans
2 shirts 1 overall
2 blouses
8 handkerchiefs
Permanent 2 double or Knits 3 blouses
Press 1 king size sheet 4 slacks
1 tablecloth 6 shirts
1 dress 4 tops
1 blouse 4 dresses
2 slacks
3 shirts
2 pillowcases
Operating Tips.It is recommended that fiberglass
items not be washed in coin-operated
washers. If these items are washed in
the washer, run the washer through a
complete cycle to rinse any residue
away that might be left in the washer.
Moving the washer toa new location...Wedge blanket
between tub ring
and cabinet top.
Remove front legs.
Tape 2
sides.
Tape rear
legs in “up”
position.
Note: Do Not
place blanket
in this area
(switch).
• Remove the front legs from the
base of the washer.
• Place both rear leveling legs in the
upper position and tape securely.
• Apply tape to the side and bottom
of the cabinet near the rear.
• Open washer lid, wedge a blanket
between the tub ring and the
cabinet top restricting the tub
movement.
• Handle washer carefully. Do Not
drop washer while using hand truck.
PAGE 6
Explosion Hazard
Never place items in the washer that
are dampened with gasoline or
other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever
had any type of oil on it (including
cooking oils).
Doing so can result in death,
explosion, or fire.
WARNING
Check list for washeroperation.Check the following if the washer is
not operating properly:
1.Power supply cord is plugged in.
2.Circuit breaker is not tripped or
house fuse blown.
3.Timer has been advanced to start
of a cycle.
4.Water faucets are turned on.
5.Inlet and drain hoses are not kinked.
6.Washer lid is closed.
7.Inlet valve is frozen if not protected
from the weather.
8.Suds level. Excess suds will slow the
spin and cause poor rinsing.
Operate the washer through a
complete cycle with no detergent.
Use less detergent or a controlled
suds type detergent in future loads.
Owner options (coin-operated models)CAUTION: Disconnect power cord.
1.For EXTRA SPIN and/or EXTRA WASH.
• Remove meter case service
door
• Loosen (2) screws on the timer
mounting bracket and lift the
timer out.
(2) screws
a. EXTRA WASH— 3 minutes.
• Connect LBU to LBU2.
• Disconnect GY from GY2.
• Set timer clutch arm as shown
below.
b. EXTRA SPIN— 2 minutes.
• Connect BK to BK2
2.For WARM RINSE and WATER SAVER:
• Remove screws from each end
of the console bottom.
• Pull the console bottom
forward; lift and tilt it back.
a. WARM RINSE
• Connect J1 to J2
b. SAVE WATER
• Pull out tab on water-level
switch.
3.If use of a larger coin vault, lock
and key is desired, conversion bar
in lower portion of coin vault area
can be removed.
4.If additional security is needed, top
and cabinet can be locked to
washer back panel by using a
“screw type” lock and key in space
provided in top panel under
console. The “screw type” lock and
key are available from usual
industry sources.
Extra Wash Standard Wash
Leave “⊥” on timer
shaft aligned with “⊥”
on timer and move
timer clutch arm to
“extra” wash position.