Now start...

With pump in room where it will be installed.

1 . Determine where you wish to locate water pump and water

bottle. The water bottle and water pump should be installed on the same level.

The water bottle and water pump must be located close together since the tubing connecting the pump to the water bottle is 1.8m (6 feet) long. Use existing tubing between water pump and water bottle. Do Not cut this tubing or add tubing between pump and water bottle. Do Not remove clamp on end of tubing that connects inner tubing to outer tubing.

Suggested locations:

l Under the sink .

l Cabinet next to refrigerator.

Determine where you will need 2 . to run water lines and the

length of tubing that will be needed. If more tubing is needed than what is supplied, tubing (Part No. 4319151) and tubing connectors (Part No. 4319153) can be obtained from your dealer or authorized parts distributor.

3Attach bottle cap to water

’bottle. Push the tubing into the water bottle until the end of the tubing reaches the bottom of the bottle. Do Not remove clamp from end of tubing.

4 , Insert one end of the outlet tubing into connector located

on outside of pump as far as it will go, If tubing needs to be adjusted, push connector in and pull tubing out.

Route the tubing to the

5 refrigerator. Cut tubing to

’length needed.

6Plug power supply cord into

’earthed, electrical outlet. Press the pump switch to the “I” position.

connector

tubing

collet

7, Run enough water through refrigerator to fill a glass or other

container. Check all connections for leaks.

If a connection leaks, push in collet and remove tubing. Cut off 1.3cm (l/2”) of tubing and reinsert into connector.

If unit is connected ONLY to a refrigerator icemaker, the icemaker will have to call for water before pump can be checked for leaks.

Information

The water pump operates

automatically when dispenser is operated. When the dispenser is released, the water pump

automatically stops operating.

When water bottle empties during use: Pressurized air is expelled through dispenser when water bottle is

empty.

1 Stop dispensing from the

’refrigerator.

2 Press the switch on the n water pump to the “0”

position.

3. Remove bottle cap from water bottle. Replace empty water

bottle Attach bottle cap to full water bottle

Press the switch on the water pump to the “I” position.

If water bottle empties while unattended, the pump will run for

2-l /2 minutes and then automatically shut off.

1. Press the switch on the water pump to the “0” position.

2. ?emove bottle cap from water mottle. Replace empty water

bottle. Attach bottle cap to full water bottle.

3. Press the switch on the water pump to the “I” position.

If water system is exposed to

temperatures below 0°C (32’F),

the system must be drained.

Remove tube from bottle. Open all outlets and run pump to inject air through all outlets.

Cleaning and sanitizing system:

System should be cleaned after extended periods of non-use.

1 Add one-half teaspoon of

n chlorine bleach to one gallon of water.

2. Inset-t tube into solution and start w-w

3. Open all outlets to fill system with solution. Let stand five minutes.

4, Flush system with water until chlorine is removed.

Panel B

Page 2 Page 4
Page 3
Image 3
Whirlpool 4373526 installation instructions Now start, Information
Page 2 Page 4

4373526 specifications

The Whirlpool 4373526 is a highly regarded refrigerator water filter designed to ensure that your drinking water and ice supply remains pure and free of contaminants. As an essential component for many Whirlpool refrigerators, this filter is notorious for its performance and reliability.

One of the main features of the Whirlpool 4373526 is its ability to reduce a wide array of impurities found in water. This includes harmful contaminants such as lead, chlorine, and sediment, making it a vital addition for those concerned about their water quality. The filter utilizes advanced filtration technologies, ensuring that the water dispensed from the refrigerator is not only clean but also tastes fresh.

The replacement process for the Whirlpool 4373526 filter is straightforward and user-friendly, designed to minimize any hassle. Users can typically replace the filter without the use of tools, making it a convenient option for busy households. The filter is engineered to fit securely into the refrigerator’s designated filter compartment and is compatible with a range of Whirlpool refrigerator models.

The longevity of the Whirlpool 4373526 is another significant advantage. This filter is designed to last up to six months or filter up to 200 gallons of water before needing replacement. This longevity not only offers economic benefits but also encourages consumers to maintain consistent water quality without frequent changes.

Moreover, the Whirlpool 4373526 is NSF certified, which means it meets stringent safety and performance standards. This certification provides an additional layer of assurance to consumers, reinforcing the filter’s capability to deliver fresh and safe water.

The sleek design of the Whirlpool 4373526 also fits seamlessly into modern kitchen aesthetics, making it visually appealing while serving its essential purpose.

In conclusion, the Whirlpool 4373526 is an efficient water filter that brings peace of mind to households by providing clean, safe, and great-tasting water. Its user-friendly installation, impressive filtration capabilities, long-lasting performance, and certification make it a top choice for consumers looking to enhance their drinking water quality. For anyone with a Whirlpool refrigerator, investing in the 4373526 filter is a crucial step towards ensuring optimal water and ice freshness.
Top Page Image Contents