INSTALLATION INSTRUCTIONS

Tools and Parts

Check that you have everything necessary for correct installation. Proper installation is your responsibility.

A level floor with a maximum slope of 1 in. (2.5 cm) under entire dryer. (If slope is greater than 1 in. [2.5 cm], install Extended Dryer Feet Kit, Part No. 279810.) Clothes may not tumble properly and models with automatic sensor cycles may not operate correctly if dryer is not level.

Flat-blade screwdriver

Adjustable wrench that opens to 1 in. (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)

Level

#2 Phillips screwdriver

Vent clamps

Tin snips (new vent installations)

Safety glasses

Caulking gun and compound (for installing new exhaust vent)

Gloves

Wire stripper (direct wire installations)

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

4 leveling legs

Parts needed:

Check local codes. Check existing electrical supply and venting and see “Electrical Requirements” and “Venting Requirements” before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please reference the “Assistance or Service” section of your “Dryer User Instructions.”

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

A location that allows for proper exhaust installation. See “Venting Requirements.”

A separate 30 amp circuit.

A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

A sturdy floor to support the total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.

Dryer Dimensions

1.Small Opening Side-Swing Door

2.Large Opening Side-Swing Door

3.Wide Opening Side-Swing Door

4.Wide Opening Hamper Door

*Most installations require a minimum 5½ in. (14 cm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”

Minimum installation spacing for recessed area or closet installation

The dimensions shown following are for the minimum spacing allowed.

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

2

Page 2
Image 2
Whirlpool 8535899 installation instructions Tools and Parts, Location Requirements

8535899 specifications

The Whirlpool 8535899 is an innovative and highly efficient appliance designed to enhance the functionality of home kitchens. As a critical component in Whirlpool's extensive array of products, this particular model often serves as a replacement part, providing longevity and reliability to users.

One of the standout features of the Whirlpool 8535899 is its durability. Designed to withstand the rigors of daily use, it typically consists of high-quality materials that ensure a long lifespan. This durability is crucial for homeowners seeking a dependable appliance, as it reduces the need for frequent replacements and repairs.

The Whirlpool 8535899 is engineered with advanced technology in mind. It often incorporates user-friendly controls that make operation intuitive, allowing users to navigate settings effortlessly. This ease of use is complemented by efficient energy consumption, as the model is designed to be eco-friendly while maintaining outstanding performance. Whether it’s for cooking, food preservation, or cleaning, the appliance's efficiency translates into lower utility bills and reduced environmental impact.

Another defining characteristic of the Whirlpool 8535899 is its adaptability. This model generally fits a variety of kitchen configurations, making it suitable for both small and large homes. Its sleek design and modern aesthetic also ensure that it blends seamlessly into any kitchen decor, providing both functionality and style.

Additionally, the Whirlpool 8535899 is often equipped with features that enhance user convenience. These may include adjustable racks, quick-connect options, and versatile settings that cater to different cooking or cleaning needs. This flexibility is particularly beneficial for families that require an appliance capable of handling various tasks simultaneously.

Maintenance is a breeze with the Whirlpool 8535899 as well. Many users appreciate the easy-to-clean components that help maintain hygiene and cleanliness with minimal effort. Moreover, the availability of replacement parts further emphasizes Whirlpool's commitment to customer support and product longevity.

In conclusion, the Whirlpool 8535899 stands out in the appliance market for its durability, advanced features, energy efficiency, and user-friendly design. Ideal for those seeking a reliable home appliance, it represents a harmonious blend of innovation and practicality, making it a valuable addition to any kitchen.