INSTALLATION INSTRUCTIONS

Tools and Parts

Tools needed

Gather the required tools and parts before starting installation. Read and follow the safety instructions provided with any tools listed here.

Flat-blade screwdriver

Caulking gun and

Level

 

compound (for installing

 

new exhaust vent)

 

Adjustable wrench

 

Tin snips (new vent

 

 

Vent clamps

 

installations)

Parts supplied

Remove parts package from the dryer drum. Check that all parts listed are included.

1

- Cycle Control (timer)

2

- cord brackets

 

 

knob

2

- screws

 

1

- Push to Start button

 

 

 

4

- casters

 

 

 

Parts needed

Check local codes, existing electrical supply and venting, and see “Venting Requirements” and “Electrical Requirements” before purchasing parts.

Mobile home installations require metal exhaust system hardware

Permanent installations require 4 dryer feet

For ordering information, please reference the “Assistance or Service” section of this manual. You can also contact the dealer from whom you purchased your dryer.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

A location that allows for proper exhaust installation. See “Venting Requirements.”

A 120-volt, 60-hz., AC-only, 15- or 20-amp circuit.

A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See “Electrical Requirements.”

A sturdy floor to support the dryer weight (dryer and load) of 115 lbs (52 kg). The combined weight of a companion appliance should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.

Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

*20 3 4" (52.7 cm)

31"(78.7 cm)

23 7 8"

(60.6 cm)

†Height with caster is 32½" (82.6 cm)

*Most installations require a minimum 5½" (14.0 cm) clearance behind the dryer for the exhaust vent with elbows. See “Venting Requirements.”

Minimum installation spacing for recessed area and closet installation

The following dimensions shown are for the minimum spacing allowed when the unit is to be operated with, or without, the Stack Stand Kit. To purchase a Stack Stand Kit, see “Assistance or Service.”

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door, and floor moldings.

Additional spacing of 1" (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Companion appliance spacing should also be considered.

4

Page 4
Image 4
Whirlpool 8578198 manual Installation Instructions, Tools and Parts, Location Requirements

8578198 specifications

The Whirlpool 8578198 is a high-quality range appliance designed to elevate the cooking experience in any kitchen. Known primarily as a cooking element, this part is made specifically for various Whirlpool models, ensuring compatibility and reliability. One of its standout features is the high-performance heating element that guarantees even cooking results, making it easier to prepare meals to perfection.

This component is designed with user convenience in mind. Its powerful output ensures rapid heating, significantly reducing the time needed to bring pots to boiling temperatures or to sear meats. Combined with a consistent and stable temperature, it allows for precision cooking, which is essential for recipes that require strict temperature control. This ability to maintain heat effectively leads to improved cooking accuracy and can prevent overcooking or undercooking, which is particularly important for delicate dishes.

In addition to its heating efficiency, the Whirlpool 8578198 is also crafted for durability. Made from robust materials that withstand high temperatures and heavy use, this component promises long-lasting performance. The thoughtful engineering behind the design minimizes the risk of wear and tear, thus reducing the need for frequent replacements, which can be both costly and inconvenient.

The Whirlpool 8578198 also features easy installation, making it a suitable choice for both professional repair technicians and DIY enthusiasts. The straightforward design allows users to replace their old or malfunctioning heating elements without needing specialized tools or extensive mechanical knowledge.

When it comes to safety, Whirlpool has prioritized user protection in the design of the 8578198. The part includes safety features that protect against overheating and short-circuiting, ensuring peace of mind while cooking. In addition, it is tested rigorously to meet various safety standards set by regulatory bodies.

In summary, the Whirlpool 8578198 heating element combines efficiency, durability, and safety, making it an essential component for anyone seeking to enhance their kitchen experience. With its ability to provide even heating and support precision cooking, it stands out as a reliable choice for transforming home cooking into a professional-like experience. Whether you are a novice or an experienced chef, this appliance is designed to meet a variety of culinary needs and elevate your overall cooking performance.